G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through February 01, 2010 » Newby Uly Questions « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Bluzm2
Posted on Friday, January 22, 2010 - 05:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

This is the 2nd time I tried to start this thread, damn computer ate it...

A while back (month or so) someone posted some part numbers, I can't find them now.
The first was for the item in the picture below (I snagged your picture from another thread Court, Thanks!).

The second is for the wiring shield that's mounted on the left side frame above the oil cooler to protect the wires going to the handlebar controls. Sorry, I couldn't find that post either.

Any other suggestions for things to check on a 06 Uly would be appreciated.

Brad

One of the first things I'm installing is the comfort Kit, just need to find one...





(Message edited by bluzm2 on January 22, 2010)
Top of pagePrevious messageNext messageBottom of page Link to this message

Etennuly
Posted on Friday, January 22, 2010 - 05:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

That is a seat spacer block. I ordered a new '06 low seat back in '06 and it came with one. It keeps the seat pan from rubbing on the ecm plugs. Two are better than one.

In some cases it is better to mount that one on the back bolt of the ecm, because with it at the front the pan on some bikes can still touch the ecm plugs.

Sorry I don't have the PN.
Top of pagePrevious messageNext messageBottom of page Link to this message

Gamdh
Posted on Friday, January 22, 2010 - 06:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Try these

For the block
1. Travel Limiter, N0903.1AK
2. Socket head cap screw, AA0410.2CZB

Wire Guide Upper Y1000.2AK
Top of pagePrevious messageNext messageBottom of page Link to this message

Bluzm2
Posted on Friday, January 22, 2010 - 09:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Michael, you rock! Thanks.

Brad
Top of pagePrevious messageNext messageBottom of page Link to this message

Mnrider
Posted on Saturday, January 23, 2010 - 12:13 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

You may want to look at the #77 connector under the front sprocket cover.
Its a heavy red and black wire connector,some have seen melting and charging problems.
Then there's the rear wheel bearings and front engine mount to check.
Top of pagePrevious messageNext messageBottom of page Link to this message

Pso
Posted on Saturday, January 23, 2010 - 11:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

In addition to the above (specificaly the #77 plug) you might want to check the wire guard upgrade at the steering head (left side where wires come from headlight going onto frame). Also make sure all recalls done, side stand and BAS.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bluzm2
Posted on Sunday, January 24, 2010 - 02:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Pso,
That's the above Wire Guide Upper
(I think...).

That's the one I meant anyway..

Brad
Top of pagePrevious messageNext messageBottom of page Link to this message

Gamdh
Posted on Sunday, January 24, 2010 - 02:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yes, the part number above is that part....
The part bag has this (have not put mine on yet)

Y1000.2AK
Bracket, Front Wire Harness

(Message edited by gamdh on January 24, 2010)
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Sunday, January 24, 2010 - 03:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Check the cable guide for the clutch cable right next to the front exhaust pipe where it exits the head.
Don't use the torque spec. in the book for the oil drain plugs, it will strip the aluminum threads. Just snug these up, the o-ring will do the sealing.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration