G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through May 16, 2013 » Head gasket job « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Wolk625
Posted on Wednesday, April 24, 2013 - 02:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So it's looking like I'm going to need to replace my rear head gasket - got quite a bit of dribble coming out around it and some light smoke at full temp.. I have the full shop manual and an upbeat attitude, but am wondering what all else I might encounter along the way - what specialty tools will I need (if any) for the head bolts? What else should I check/consider replacing on my way down in there and back? Is it even something I should be able to handle or leave it to professionals to do?
Top of pagePrevious messageNext messageBottom of page Link to this message

Kilroy
Posted on Wednesday, April 24, 2013 - 02:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Make sure is isn't your rocker box gaskets that are leaking and making it appear to be your head gasket. Could save you a lot of effort, and they are notorious for leaking, especially if they are still the originals.
Top of pagePrevious messageNext messageBottom of page Link to this message

Firemanjim
Posted on Wednesday, April 24, 2013 - 03:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

As a rule the head gasket will not leak oil, look at rocker boxes and pushrod seals .
Top of pagePrevious messageNext messageBottom of page Link to this message

Wolk625
Posted on Wednesday, April 24, 2013 - 04:34 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I know for fact that the bottom rocker gasket is good, because that was the first thing that I replaced when I noticed the wet spot months ago, and that this spot is smaller and lower than the first one. The oil spot starts below the rear exhaust port and down - everything above that is dry. If it were the pushrod seals I would think I would see more oil in the area of those seals but those seem pretty clean. Would it be possible for oil to get pulled into/past the exhaust valve shaft and be expelled in the exhaust, and what I may be seeing is oil from that seeping through a bad rear header gasket seal? What else could explain my smoke?
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Wednesday, April 24, 2013 - 05:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

FMJ covered it,
the standard box is 3 pieces so look close.

IMO a valve guide seal will not show up outside in most cases and would smoke like the dickens, the OIL return hole is near a corner of the jug

Sorry I had pix of the top end job i did some time back and was going to post up but I can't find em,

Looking at a damaged jug I keep as a book end, there is an oil passage on the front jug,
If you are facing the motor at the front of the bike its on the front right corner of the jug,(opposite the push rods) the oil passes thru an oring-ed dowel down thru the base gasket into the bottom end, It seems like its on the wrong side of the motor. Ymmv
Top of pagePrevious messageNext messageBottom of page Link to this message

Wolk625
Posted on Thursday, April 25, 2013 - 05:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Just going to share what I am seeing - may or may not help some:







When the rocker box was leaking it was obvious with the oozing from the bottom of it, but this leak has been present before and after that one. I am beginning to fear if this is a sign that my piston rings are going bad and that's how I've got oil coming from there..
Top of pagePrevious messageNext messageBottom of page Link to this message

Essmjay
Posted on Thursday, April 25, 2013 - 05:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yep. Head gasket. Doesn't mean your rings are bad though. If it was me, with riding season here, I would just pull that head and remove the jug with the piston enclosed. (Pull the wrist pin and remove the jug and piston together). You will have to replace the head gasket and base gasket but you should be able to reuse the rockerbox gaskets. You can visually inspect the bore and piston and if it looks okay, put it back together. Then next winter you can think about going through the whole top end. Do not attempt to only replace the head gasket, you will only find the base gasket leaking shortly after you put it back together.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bluzm2
Posted on Friday, April 26, 2013 - 12:37 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

What Shane said...
Top of pagePrevious messageNext messageBottom of page Link to this message

Kevmean
Posted on Friday, April 26, 2013 - 06:54 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Or before you tear it to pieces just try retorquing the head bolts and see if it cures it (it did on my X1 ; )
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Friday, April 26, 2013 - 08:21 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Why mess with the circlips and wrist pin? Seems easier to just pull the jug and leave the cylinder in place. It's not that hard to get the rings back in place and into the jug.

I'd be nervous re-using circlips, and they are a hassle to get in and have confidence that you got them in trying to put them in with the jug in the way (in my limited experience).
Top of pagePrevious messageNext messageBottom of page Link to this message

Purpony
Posted on Friday, April 26, 2013 - 10:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I left the cylinder in place and just pulled the jug... Was very easy to slide the piston/rings back into the jug. I borrowed a friends piston/ring tool and didnt even use it.

Always replace your base gasket when you do a head gasket.

It was a pretty straight forward easy fix.
Top of pagePrevious messageNext messageBottom of page Link to this message

Essmjay
Posted on Friday, April 26, 2013 - 11:00 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The reason I would leave the piston in the jug for this job is that the existing rings have worn into the cylinder wall. If you pull the piston out the rings will never line up again with the existing lands and grooves. (You may not be able to see them, but they are there.) If you pull the piston out you should at the very least run a hone through the cylinder before reinstalling the piston. At that point you may as well do it right and just do a full top end job with new rings and a cylinder bore to match. but if you just want to get onto the road with minimal cost or wear and tear, leave the piston in place. You can easily buy new wrist pin circlips, in fact you should never reuse those little buggers.
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Friday, April 26, 2013 - 06:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yes head gasket leaking at the oring
I would change it out, the gasket is going to fail completely at some point,

You might try the re-torque nothing to loose except some time....
Top of pagePrevious messageNext messageBottom of page Link to this message

Wolk625
Posted on Saturday, April 27, 2013 - 01:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

My eventual goal was to replace both head and base gaskets eventually at some point but it's looking like I should be looking into that a lot sooner than I originally planned. Both ideas for the piston do seem to have good reason why to do it that way, so my end decision will probably be made when I can pull the head and assess what I'm working with. For this "re-torque" being mentioned, is this similar to the manual's technique of - torque once then completely un-torque then re-torque again, or is it simply cracking the bolts loose then re-tightening to spec torque? Thanks for all the responses guys.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jolly
Posted on Sunday, April 28, 2013 - 09:05 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

my S3 just started leaking at the base gasket rear cylinder...fun! grrr looks like Im in the same boat as you..and here we go down the rabbit hole, this motor has a fresh rebuild from the last owner but it does not have the xb rocker box conversion so now I've got to do a base gasket and the xb conversion;. let me know if you ended up pulling the cylinder with the piston in or if you just pulled the jug and re-inserted the piston? I would not have thought that the rings seating would have made that much of a deal on these bikes to be concerned with it after the motor is broken in and your re-inserting the same piston and rings (not worn out)...
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration