G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through August 19, 2009 » HELP PLEASE ! « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Twowheeltony1
Posted on Wednesday, August 05, 2009 - 06:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I recently purchased a ecm spy cable w/map to use on my 99 x1 bike ran good before i used the spy cable , during this first session i had the idleing on a swingarm stand just browsing the the different functions and the bike just stalled , after it stalled it has three codes ,short to ground for fuel pump ,iat sensor and ecm ?? now bike will not start it just back fires threw the intake and exhaust ???
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Wednesday, August 05, 2009 - 08:35 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

possible un related fault

did you try to burn any thing to the eeprom in the ecm ??

did you try to read the prom ?

just monitoring & browsing should not harm the ecm.

check the tps and afv values power on not runing I will check back this evening

gotta go
Top of pagePrevious messageNext messageBottom of page Link to this message

Twowheeltony1
Posted on Wednesday, August 05, 2009 - 04:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

after the bike stalled i did burn a race map to the eprom and then the text only but no luck so i put it back to the stock map , i did find a broken ground wire but i fixed it and still the same .
Top of pagePrevious messageNext messageBottom of page Link to this message

Twowheeltony1
Posted on Wednesday, August 05, 2009 - 09:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I also found that the lead terminals on the cheap battery are both cracked almost all the way across ?? could this have something to do with it ? the three codes are 33 35 44 .
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Wednesday, August 05, 2009 - 11:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yes the loss of the ground to a sensor or a connection can cause erratic and no operation, repair / replace battery terms and check wiring connections.

the faults indicate power losses I believe

33 fuel pump
35 tach
44 bank angle sensor

check wiring connectors at ecm and other places the device connectors for these fault items are all over the bike.

double check the instructions for ee prom down load, reload your stock setup for now,

oh and check wiring
Top of pagePrevious messageNext messageBottom of page Link to this message

Twowheeltony1
Posted on Sunday, August 09, 2009 - 04:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

i got a new batt and fixed the broken ground ,cleaned the terminals of the fuel pump connectors. checked iat wires they look good . things i did to bike just before this problem , starter gasket ,new/used head pipe, renthal bars ,kuryakyn filter adapter w/tall plastic velocity stack w/screen both from asb . and bike ran fine before , but only ran for 3 or 4 min stalled during monitoring waiting for opperating temp .like i said before wont run ,starts for maybe 1 sec , some times it will only back fire out the exhaust or threw the intake .and has codes for inertia switch short to ground ,fuel pump short to ground and iat short to ground . not sure what to do next?
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Sunday, August 09, 2009 - 08:46 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Tony, investigate the indicated problems, My copy of ecm spy indicates short to ground for an open circuit, check the grey and black connectors on the ecm and the wiring there, then one by one investigate
the other connectors,

either there is a wiring problem or the ecm is an issue,
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration