G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Archive through April 08, 2010 » Head Neck Bearings replacement Question? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Hogs
Posted on Friday, April 02, 2010 - 12:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Anyone ever replace there neck bearings and any special tools or hints ya can give to do so???
Just what type of a job is it to get into?
Thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Friday, April 02, 2010 - 12:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The service manual lists a bunch of tools for the job, but I've only glanced at the procedure so I won't say any more.
Top of pagePrevious messageNext messageBottom of page Link to this message

Whitexc
Posted on Friday, April 02, 2010 - 09:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Not to jack your thread Hogs, but is there a way to check the steering head bearings without having the pull scale in the manual? I am doing the 10k on the bike and want/need to check them but don't have that tool.
Top of pagePrevious messageNext messageBottom of page Link to this message

Akbuell
Posted on Saturday, April 03, 2010 - 11:52 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Whitexc- I went to a sporting goods store and got a cheapo fish scale. Not very expensive. Then went to the grocery store (after checking w/a dictionary to find the correct weight) and 'calibrated' the scale by weighing a gallon of water. Will get you in the ballpark when doing the pull test.

Hope this helps, Dave
Top of pagePrevious messageNext messageBottom of page Link to this message

Hogs
Posted on Saturday, April 03, 2010 - 05:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Hmmm Would have thought there wd. of been some that got into replacing the neck bearings by now....

Maybe some will see this over the weekend though...
Top of pagePrevious messageNext messageBottom of page Link to this message

Whitexc
Posted on Sunday, April 04, 2010 - 07:49 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Good idea....and good luck Hogs. I hope you find the info you are after.
Top of pagePrevious messageNext messageBottom of page Link to this message

Starter
Posted on Sunday, April 04, 2010 - 08:19 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Jack it up using the front jack point, prefered to use a rear stand as well for stability. Remove front wheel, mudgaurd, hang caliper under the upper fairing, remove forks, then top triple, knock the lower out with the steering stem.

Easy as if the steering stem isn't seized in the inners of the bearing. Take note the orientation of the bearing. Just knock the lower bearing out with a drift and hammer, then sit on the floor and knock the upper out in the same fashion. Buell even put little notches in the frame so it is easier. Pull them in using threaded rod and a suitable asortment of washers. If you really rough knock them in using a socket on the outter race and hammer. Re-assemble. To get the front end in alignment, install the forks into the triples and leave the bolts semi loose (but still holding) as well as the top capnut, then install the wheel and the triples will align. Then jingle it around and progressly tighten the fastners.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration