G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through August 12, 2008 » Crusty Axle, Help! Advice needed « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Not_purple_s2
Posted on Wednesday, August 06, 2008 - 07:40 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So I anihalated my rear tire this weekend (steel showing) and ordered a new one that should show up tomorrow. So today i went to remove the rear wheel so I can take it in and have the tire mounted at a local shop. But when I started backing the axle out I noticed this...

the axle is corroded on the left side and the wasn't sliding over. I tried carefully tapping around on the wheel, swingarm, and axle ends hoping it might break lose but the corrosion is too much.

Any Advice? Do I need to get a truck and haul it into the dealership? I wouldn't dare drive all the way to Pensacola with steel showing in the tires.
Top of pagePrevious messageNext messageBottom of page Link to this message

Teeps
Posted on Wednesday, August 06, 2008 - 08:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Get a brass wire brush and some penetrating oil of your choice. Squirt, brush, repeat until the axle is free.
I would suggest replacing the wheel bearings too, just in case.

When reinstalling the axle be sure to slather it with anti seize compound.

Also don't over torque the axle.
Top of pagePrevious messageNext messageBottom of page Link to this message

Whitexc
Posted on Wednesday, August 06, 2008 - 08:34 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

PB Blaster...spray it up and let it sit for a bit, then wire brush it and work it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Not_purple_s2
Posted on Thursday, August 07, 2008 - 07:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It's out, thanks guys.
Yeah PB Blaster, a wire brush, and some firm but gentle persuasion and it came right out.
Other than the corrosion the wheel removal was a snap.
Top of pagePrevious messageNext messageBottom of page Link to this message

Etennuly
Posted on Thursday, August 07, 2008 - 08:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

There is obvious water intrusion there. Pick the seals out of the wheel bearings, check them closely for rust. If you see any you can save a lot of trouble by replacing them now. If they have no rust you can smear in a little fresh wheel bearing grease and the seals will push right back in.

Looks like you'll need to clean up that axle and coat it with anti-sieze to make it come out easier next time. I wipe a coat of the anti-sieze on the outside of the seal to help make it waterproof.
Top of pagePrevious messageNext messageBottom of page Link to this message

Not_purple_s2
Posted on Thursday, August 07, 2008 - 10:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It seems that portion of the axle sits inside a kind of sleeve portion of the swingarm which held moisture on it.
The rest of the axle was in great shape, clean, no corrosion.
Top of pagePrevious messageNext messageBottom of page Link to this message

Beachbuell
Posted on Thursday, August 07, 2008 - 11:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I always hit my axles with some sandpaper, brake clean and then anti seize lube upon install.
Top of pagePrevious messageNext messageBottom of page Link to this message

Blake
Posted on Friday, August 08, 2008 - 03:57 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I dig your profile photo Curtis.

« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration