G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through March 29, 2005 » Dangit!!! Ok, got a bit of a problem here. My fault. « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Saturday, March 26, 2005 - 09:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Well, today I noticed the Lighting logo on the fly screen was starting to peel. So, I went and got some super glue. While putting it on some of the glue ran. Well, now a have an small area just under the logo that's a small hazy white. I've buffed it with just about anything I can think of and only gotta bit of it off. Anyone know of anything that will take this crap off? If not, how much does a fly screen for the 9SX cost?
Top of pagePrevious messageNext messageBottom of page Link to this message

Keith
Posted on Saturday, March 26, 2005 - 10:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Cataract2,

I don't know the answer to your question, but Daves can hook you up with a new fly screen.
Top of pagePrevious messageNext messageBottom of page Link to this message

Xring
Posted on Sunday, March 27, 2005 - 12:32 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Fingernail polish remover (acetone) will remove superglue. Don't know what it will do to the Buell plastic, though.

Good luck,
Bill
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Sunday, March 27, 2005 - 01:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Tried it. That sucker is on there good. Might take another shot at it later. If it doesn't work I'm calling Dave.
Top of pagePrevious messageNext messageBottom of page Link to this message

Joele
Posted on Sunday, March 27, 2005 - 03:00 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Most cyanoacrylate remover actually dissolves plastic - so avoid that. Acetone would be the next logical choice but you have to soak and again, don't know what that would do to the fly screen.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Sunday, March 27, 2005 - 07:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Novus 3 will go a long way if you have the patience. You will have to get the superglue off first, maybe with something like 1600 grit sandpaper, then novus 3 then novus 2 then the harley glaze.

If the flyscreen is expensive, I have a "donor airbox" that I can experiment with to see if you can do the really high grit paper and recover it with novus.
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Sunday, March 27, 2005 - 09:00 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'll give that a run. Novus 3 did get some of the glue off. Looks like it will take some elbow grease.
Top of pagePrevious messageNext messageBottom of page Link to this message

Slaughter
Posted on Sunday, March 27, 2005 - 09:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Methanol is the standard solvent for hardened superglue but yeah, try it on a corner first in case it dissolves the flyscreen.

Hobby shops selling model airplanes usually have solvent for cleaning dried superglue
Top of pagePrevious messageNext messageBottom of page Link to this message

Rigga
Posted on Sunday, March 27, 2005 - 10:15 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

get yourself a very sharp flat blade,like a hobby/craft knife and gently use the sharp edge to remove the glue.... i had the same thing happen when i spilt some on my carbon hugger,lifted it right off,polished afterwards and now never knew it was there
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration