G oog le Buell 1125R Forum | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » 1125R Superbike Board » Stator/Voltage Regulator/Charging System subforum » Stator Check « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Tbowdre
Posted on Wednesday, April 20, 2011 - 02:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I am off on a road trip the end of June and I thought I would check my stator..... (no i will not sell my bike, please do not tell me to just ride- thank you)

I am just getting started and from what the service manual reads (and badweb posts) it seems the wires from the stator are supposed to be IN the plastic channel NOT floating next to the engine.

Thanks Biggs HD

So it looks like i have met my first hurdle.

I suppose I will have to decide if the wires are dong okay outside of the channel and see how hard it might be to fish it up an into the channel when reinstalling

has anyone else had to deal with trying to get the wires back in the correct routing?

thanks todd
Top of pagePrevious messageNext messageBottom of page Link to this message

Froader4life
Posted on Wednesday, April 20, 2011 - 02:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Have you had bad luck with Biggs? I too am from north county SD and deal with Don there. Haven't had any major issues with them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tbowdre
Posted on Wednesday, April 20, 2011 - 03:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

no REAL issues with Biggs. I did the VR on my own dime because they could not duplicate the problem. (system voltage intermittent error with issue overcharging battery) oh well. They did my stator and it is still working. Oh, when they did my harness upgrade they "forgot" to reattach my charcoal canister.

back on topic:

After further investigation I can not really tell where the wires are supposed to go.... maybe they are supposed to be floating near the engine? anyone happen to have a pick of correct routing of stator wires.

Search here and service manual are no help.

thanks, todd
Top of pagePrevious messageNext messageBottom of page Link to this message

1_mike
Posted on Wednesday, April 20, 2011 - 03:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Why not floating next to the engine ?

I decided since the chances are very great that a stator change or three or four times is in the cards for the 09, 1125's.

So...with that in mind, while pulling the original harness thru the plastic tunnel, and the difficulty that it was to do...that I wasn't going to put the harness thru that amount of "stretching" again...!

Both plastic (insulation) and copper (conductor) can be stretched very easily. Stretched to the point of thinning the copper measurably. And the copper wire, unlike the plastic...will not go back to it's original state.
This also effects the power it will transmit without creating heat.

So yes...for two reasons, I left mine outside the tunnel/channel, in order -
1. Possible unnoticed damage to the harness.
2. Ease of the next stator change..

And the way it can be done...without tugging on the harness...mine "appears" to be in the correct location...just esthetics ya know..!

Mike
Top of pagePrevious messageNext messageBottom of page Link to this message

Tbowdre
Posted on Wednesday, April 20, 2011 - 05:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Well the color of the epoxy is mostly a light tan and does not look over heated or fried. BUT on close inspection there are cracks all over the place.


not positive, but I think this is not good

are those folks that have used custom rewind still happy?
Top of pagePrevious messageNext messageBottom of page Link to this message

Tbowdre
Posted on Wednesday, April 20, 2011 - 05:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

thanks for the reply mike.

Ill probably just leave routing like it is, wires seem fine
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Thursday, April 21, 2011 - 01:05 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Tbowdre, far as I can tell anyone who's installed the Custom Rewind hasn't reported any complaints or issues since installing it. Talking with the guy at Custom Rewind he reports no one has returned any that they have ordered from him (Buell stators).
Top of pagePrevious messageNext messageBottom of page Link to this message

Tbowdre
Posted on Thursday, April 21, 2011 - 01:35 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Im calling custom rewind tomorrow anyone have a contact they might recommend
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration