G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through July 11, 2018 » Machined alum gas cap piece that latches or locks it to replace plastic one « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through May 13, 2018Phelan30 05-13-18  12:39 pm
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Fabfun
Posted on Sunday, May 13, 2018 - 02:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I loosened the nut even to point of flats not engaging on latching bolt so that not issue
Top of pagePrevious messageNext messageBottom of page Link to this message

Kmbuell
Posted on Sunday, May 13, 2018 - 09:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

How long since there was gas in the tank? Sometimes I find I need to soak the gasket in gas to soften it up if it’s been dry for a few months. I do it in a zip lock bad with about a 1/4 cup of gas.
Top of pagePrevious messageNext messageBottom of page Link to this message

Upthemaiden
Posted on Monday, May 14, 2018 - 09:10 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yeah it sounds like your gasket is just too tight against the new aluminum piece. You could try soaking it in gas like KM said, or maybe if that doesn't help you could just try trimming the bottom of the gasket with an xacto knife(Is it supposed to somewhat seal up against the bottom of the gas cap? I don't know if that would cause you any problems with gas leaking, I know the actual cap still has the o-ring on it). If nothing else you might just need to replace that rubber gasket. I saw someone on facebook this morning asking about replacement gaskets, was that you? You might already be a step ahead of me here if it was. If it wasn't you, someone posted a link to st. paul HD, they sell the gaskets, I think it was around $14.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ebutch
Posted on Monday, May 14, 2018 - 05:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I used a new O-ring then fined the right spot on the nut and threaded post that doesn't bine.Or maybe you got a bad-one?
Top of pagePrevious messageNext messageBottom of page Link to this message

Fabfun
Posted on Saturday, May 19, 2018 - 07:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

No wasnt me but I ordered mine from St. Paul HD Got my new rubber gasket and just installed it and works fine now thanks everyone for the help

(Message edited by fabfun on May 19, 2018)
Top of pagePrevious messageNext messageBottom of page Link to this message

Zac4mac
Posted on Wednesday, June 06, 2018 - 11:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I put one of these on my RS1200 and it works greta.

Z
Top of pagePrevious messageNext messageBottom of page Link to this message

Bluelightning
Posted on Saturday, June 23, 2018 - 03:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ok. I need one of these fixes. None on eBay right now, anyone know how to contact the guy to get one?
Top of pagePrevious messageNext messageBottom of page Link to this message

S1owner
Posted on Saturday, June 23, 2018 - 04:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Search gmann find a pist and then pm him.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration