G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through July 11, 2018 » R&R broken main shaft, '01 S3T « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through May 09, 2018Upthemaiden30 05-09-18  12:29 pm
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

S1owner
Posted on Wednesday, May 09, 2018 - 12:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ahhh that makes sense
Top of pagePrevious messageNext messageBottom of page Link to this message

Brother_in_buells
Posted on Wednesday, May 09, 2018 - 01:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ken ,a impact wrench does also work easy for removing the nut from the drive pulley.
Hold the pulley with one hand and use the other with the impact wrench and It's of in couple seconds.

Your tools do work perfect for installing and tightening the nut to the correct torque
Top of pagePrevious messageNext messageBottom of page Link to this message

S1owner
Posted on Wednesday, May 09, 2018 - 01:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Impact would not even touch mine. Used the most powerful one available and would not budge. Also impacts can cause damage to the trans
Top of pagePrevious messageNext messageBottom of page Link to this message

Williamscottrobertson
Posted on Wednesday, May 09, 2018 - 02:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I had to impact my pulley nuts on my s1 and s2 for about a minute before they came off. The pulley holder shouldn’t allow the pulley to move if it’s against the frame, and the bike should be in neutral. Everyone always says an impact could cause trans damage but i think using heat on the nut could heat the shaft and damage the seals. Just my opinion. I’ve just used a good impact and haven’t had any ill effects.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hootowl
Posted on Wednesday, May 09, 2018 - 03:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Impact tools can knock the magnets off the rotor.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buelliedan
Posted on Wednesday, May 09, 2018 - 03:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

In use impacts all the time on both sides and have never had a magnet fall off. And I have done many.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buelliedan
Posted on Wednesday, May 09, 2018 - 03:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

My impact of choice is the new Snap-on Lithium battery 1/2 drive. Puts my "Earthquake" that I used for many years to shame and no air hoses to worry about.
Top of pagePrevious messageNext messageBottom of page Link to this message

Livers
Posted on Wednesday, May 09, 2018 - 05:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've used an electric impact on the engine sprocket, clutch hub, and trans sprocket since small Milwaukee v-twins had iron heads. Never a problem.

To the OP: I want to see a picture of a broken transmission main shaft.
Top of pagePrevious messageNext messageBottom of page Link to this message

Upthemaiden
Posted on Wednesday, May 30, 2018 - 03:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ever make any progress on this?

I finally put my primary back together over the weekend and realized I was wrong. I kept thinking that even if your transmission was broken, the lock bar between the gears would still keep the clutch from spinning, letting you remove the but. I went to put mine on, put the lock bar in, and of course it started spinning. The bar only locks the outside of the clutch, but the center will spin all day.

Did you ever get yours out? What you need is someone who can weld a couple steel and fiber clutch plates together(or maybe you can just buy a tool shaped like that, I know I've seen them for mx bikes so I'm sure someone makes one for a sportster clutch), or you could drill a few and bolt them together. That'll hold both parts of the clutch together, which will let you remove that nut using a primary locking bar.

Either way, let us know what's going on with it!
Top of pagePrevious messageNext messageBottom of page Link to this message

Hootowl
Posted on Wednesday, May 30, 2018 - 05:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

^ That's a good idea.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration