G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through January 13, 2017 » Late model 08 up XL XB flywheels « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Lakes
Posted on Friday, October 28, 2016 - 12:01 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Anyone running these in Tuber's?
Top of pagePrevious messageNext messageBottom of page Link to this message

Buelliedan
Posted on Friday, October 28, 2016 - 02:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

it is a lot of work to install them as they require machining for the timken bearings on the sprocket shaft. They are not just bolt-in.

Last I saw it cost almost $1500 to do this swap in a set of 2003 and older cases.

Personally for the amount of money it cost to do one of those cranks I recommend getting an S&S crank with the splined pinion shaft. It cost less and best of all no more worries about the pinion shaft keyway breaking and causing tons of damage like the stock stuff can do.


(Message edited by buelliedan on October 28, 2016)
Top of pagePrevious messageNext messageBottom of page Link to this message

Pontlee77
Posted on Friday, October 28, 2016 - 03:13 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I use a XB9 fly wheel on my X1 and it'a direct swap.
I'm talking about what goes in the primary.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Friday, October 28, 2016 - 04:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

You mean stator bell then. Unlike UJM's. the Buell flywheel isn't the stator magnets.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buelliedan
Posted on Friday, October 28, 2016 - 04:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

"I use a XB9 fly wheel on my X1 and it's direct swap.
I'm talking about what goes in the primary."


An XB9 flywheel is not a direct swap into an X1. Are you talking about your alternator rotor and sprocket inside the primary?
Top of pagePrevious messageNext messageBottom of page Link to this message

Alfau
Posted on Friday, October 28, 2016 - 07:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Harley Sportster flywheels will be here to stay.
The others went the way of the ...




Top of pagePrevious messageNext messageBottom of page Link to this message

Lakes
Posted on Friday, October 28, 2016 - 10:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thank's Buelliedan, was only looking as so many posting about the swap, will wait till i have my stock flywheels out & apart to see what they look like. as have been runing it at very high cranking pressure for past few years, & going to 88" cast iron flat tops will weld the thunderstorm chamber for better swish, but can fit timkin as had to with twin cam. just will wait see what looks like.
Top of pagePrevious messageNext messageBottom of page Link to this message

Lakes
Posted on Friday, October 28, 2016 - 10:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Alf, yes i'm not a big fan of the late flywheels as i had my twin cam 88" carb dyna flywheels slip the crank pin was lucky to get a near new set that the owner upgraded to 114" i had crank pin welded no more trouble but my old Shovel ran 11's & i road it everywhere could rebuilt it's bottom end.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ralph
Posted on Friday, October 28, 2016 - 11:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

That photo is cruel.
Top of pagePrevious messageNext messageBottom of page Link to this message

Lakes
Posted on Sunday, October 30, 2016 - 06:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thank's all, I'll wait till I pull motor split cases & pull my stock flywheel apart to inspect it.first. As have been runing it with very high cranking pressure they have never been apart before & bike has 100,000k (60,000miles) with new build will run less cranking pressure around 200 I think, but now it is up at 230 pound
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration