G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » Old School Buell » Archive through April 02, 2013 » Forcewinder missing parts! « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellx1w
Posted on Wednesday, March 13, 2013 - 06:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have the X1 that breaks up at 4KRPM.. I was looking in more detail today at the bike , based on suggestions made here.

SOMEWHERE in the last year or so apparently one of the shops left a tube off my forcewinder! I just ordered it. And coincidentally the lady said there is ANOTHER O2 sensor inside the forcewinder which could be screwed up from the missing pipe?

Anyhow I'll see if that helps- should be here in the next week or so..

Does anyone know can I CLEAN or so any work on that internal O2 sensor.

Thanks!
Top of pagePrevious messageNext messageBottom of page Link to this message

01x1buell
Posted on Wednesday, March 13, 2013 - 06:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

it is not a o2 sensor,it is inlet air temp sensor.



if it was we i would stop messing with it until a got/ learned how to use ecm spy very simple and will pinpoint your problems
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellx1w
Posted on Wednesday, March 13, 2013 - 09:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I looked into ECM spy- Al told me it wont do anything for me unless my engine lite was on? Does that sound right? I dont have a lite on- but maybe it would still tell me whats what?
Top of pagePrevious messageNext messageBottom of page Link to this message

Kalali
Posted on Wednesday, March 13, 2013 - 09:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

What do you mean by "breaks" at 4K RPMs? What are you trying to do? What tube was missing? Please be a bit more clear so folks can help you.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellx1w
Posted on Wednesday, March 13, 2013 - 09:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

There is a tube that goes into the base of the back of the filter, next to the temp sensor tube, and from there into the tube attached to the head. It was missing. I *think* the last mechanic probably left it off.

Bike idles fine, and runs OK up to 4000 RPM. There it *acts like* its rev-limiting and wont go higher.

I can rev it all the way to redline in Neutral, no issues.

I have the RACE ECM and no changes to the bike in many miles. It just started this issue a few months ago. I checked the injectors they spray strong. Replaced the fuel pump and O2 sensor.
Top of pagePrevious messageNext messageBottom of page Link to this message

Two_seasons
Posted on Wednesday, March 13, 2013 - 09:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

This is the same bike that came back from an HD dealer with parts hanging loose, missing, after an engine rebuild that the owner had done.

There are many issues with this bike. And you do need ECMspy so you have an electronic tool in your toolbox to help you maintain and tune your bike.
Top of pagePrevious messageNext messageBottom of page Link to this message

Kalali
Posted on Wednesday, March 13, 2013 - 10:10 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

That is your breather tube and should have a split where it gets hooked to each head through separate tubes. Most folks route that to a catch can. Do a search for catch can and you'll find a lot of references to various options to get it done. As for the throttle response issue, the first place I'd check are the grounds. That includes battery connections, the junction box under the seat and the fat wire strap on the swing arm. Remove the wires and use a sand paper to clean any rust and/or paint from the washers and/or nuts. You may also want to check the ignition system starting from the plugs and then plug wires and the coil. But my money is on the ground or a cracked plug wire. Remember plug wire crack may not be visually detectable. Keep us posted on how you make out.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellx1w
Posted on Thursday, March 14, 2013 - 08:16 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

OK I'll call Al today and order the Spy cable.

No- my buell never came back with parts hanging. Mine is the the bike that the dealer left the transmission oil drained when he returned it!

THanks..
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellx1w
Posted on Thursday, March 14, 2013 - 10:30 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yes- Al at American Sport Bike said to check grounds too.. In fact it was his number 1 rule.

I'm not really sure where they all are but this weekend I'll look for ground straps.
Top of pagePrevious messageNext messageBottom of page Link to this message

01x1buell
Posted on Thursday, March 14, 2013 - 12:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)



(Message edited by 01x1buell on March 14, 2013)
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration