G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » Old School Buell » Archive through October 23, 2012 » S-3 mirror won't tighten??? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Hugie03flhr
Posted on Thursday, October 11, 2012 - 01:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

My M-2 has an S-2 fairing on it and the mirror folds in to easily. I tried tightening but the internal bolt just spins. Is there a way to stop that bolt from spinning without chewing up the outside of the mirror?
Thanks!
Top of pagePrevious messageNext messageBottom of page Link to this message

Hugie03flhr
Posted on Friday, October 12, 2012 - 04:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Nothin ??? Oh well, there's always crazy glue....
Top of pagePrevious messageNext messageBottom of page Link to this message

Triman023
Posted on Friday, October 12, 2012 - 04:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The mirror on my S2 has a rubber boot. Under the boot is a joint held together with a hex bolt, I tighten that down to keep the mirror from folding against the fairing. Is this what you are talking about? The other thing is a ball joint in the mirror housing, THAT you will have to use Crazy glue on.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hugie03flhr
Posted on Wednesday, October 17, 2012 - 09:21 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It's the hex bolt. It won't tighten or loosen anymore. It just spins so the mirror will flop in at high speed.
Thanks for any tips before I tear it all to Hell!
Top of pagePrevious messageNext messageBottom of page Link to this message

Old_dog
Posted on Saturday, October 20, 2012 - 01:34 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Had the same prob with my S3T. I pulled the bolt out, I slid (forced) a flat washer in between where the mirror stalk slips into the fairing bracket and tightened it all up. Worked like a charm. Not the factory manual solution but it worked.
Top of pagePrevious messageNext messageBottom of page Link to this message

Svmotoman
Posted on Saturday, October 20, 2012 - 11:00 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

My S3T mirror is loose too... but my hex bolt does tighten... I can tighten it all the way, but the stalk is still loose.

It appears that the nut from the upper part of the bracket may have pushed through some plastic that was holding it in?

Basically when you tighten the hex bolt, the nut just drops out of the upper portion of the bracket and onto the mirror stalk... so the bracket is not squeezing anything at that point which is how I presume it's supposed to work?
Top of pagePrevious messageNext messageBottom of page Link to this message

Svmotoman
Posted on Saturday, October 20, 2012 - 11:10 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Interesting... just happened to have a washer that fit exactly the round opening in which the nut resides... shoved it in at the top above the nut (there is enough plastic there to hold it in place so it doesn't drop out the bottom), then I tightened...

it worked.... the 2 sides of the bracket now squeeze the stalk.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hugie03flhr
Posted on Tuesday, October 23, 2012 - 01:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'll have to work that hex bolt out or drill it since the captured nut is spinning and shim it up like you guys said. I have a bunch of shims for Footpegs . Maybe they'll work....
Thanks for your help guys!
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration