G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » Old School Buell » Archive through October 02, 2012 » TPS reset rough idle « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through August 26, 2012Wack0130 08-26-12  02:11 am
Archive through August 16, 2012Wack0130 08-16-12  11:06 am
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

01x1buell
Posted on Sunday, August 26, 2012 - 09:28 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

BUEJA120 05-27-99
Reihe: 1
sorry about that.
Top of pagePrevious messageNext messageBottom of page Link to this message

Wack01
Posted on Sunday, August 26, 2012 - 12:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Wack01
Posted on Sunday, August 26, 2012 - 12:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I burned the eeprom to ecm, bike back to square one after messing around with all the electrical/computer stuff I think my problems is mechanical.

My thoughts are the bike was ran to long in lean condition in desert climate and burnt a valve?

Any thoughts here's a vid of the exhaust while cranking. It looks like fuel mist being blown out.
http://www.youtube.com/watch?v=DCseS8tqglw&feature =youtu.be
Top of pagePrevious messageNext messageBottom of page Link to this message

Wack01
Posted on Monday, August 27, 2012 - 02:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Did a compression test today 200psi front and rear WOT

My last resort is to carb it
Top of pagePrevious messageNext messageBottom of page Link to this message

5liter
Posted on Sunday, September 09, 2012 - 11:19 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Any resolution to the problem?
Top of pagePrevious messageNext messageBottom of page Link to this message

Psykick_machanik
Posted on Sunday, September 09, 2012 - 04:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

After watching your vid it looks like a timing problem to me.
Did you make sure the plug wires are on the right cyl.?
Hope you get this resolved, sounds really frustrating.
Top of pagePrevious messageNext messageBottom of page Link to this message

Wack01
Posted on Thursday, September 13, 2012 - 05:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

No timing is spot on with tdc of front cylinder coil connected right,
compression good
fuel pump good
injectors clean
tps good
I even replaced the ecm with an race one
still no idle
I ordered an extra wiring harness
and VOES
I have a spare carb and coil
time to convert
Top of pagePrevious messageNext messageBottom of page Link to this message

Wack01
Posted on Thursday, September 13, 2012 - 05:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I waiting for part to arrive
in mean time I been tinkering with my 91 vw diesel I getting in hypermilling
Top of pagePrevious messageNext messageBottom of page Link to this message

Wack01
Posted on Thursday, September 20, 2012 - 10:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Well I got the bike running. After much frustration I borrowed the carb/manifold off my 98 s3. Bike runs great

I'm on the hunt for another fuel pump since that's the only piece yet to be replaced.

I don't understand why the other pump is failing it pumps out 48psi. Any thoughts?

I don't want to leave it carb without the voes, Unless using the bike can still advance the timing to avoid detonation with the stock ecm. Anybody running this set up?

http://www.youtube.com/watch?v=WZRvsjbiW9w
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration