G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » Old School Buell » Archive through June 03, 2010 » Removing oxygen sensor??? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Kfry
Posted on Monday, May 24, 2010 - 10:31 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

trying to take off aftermarket exhaust. welded together completely. i need the oxygen sensor removed for it to come out. any ideas?
Top of pagePrevious messageNext messageBottom of page Link to this message

Andymnelson
Posted on Monday, May 24, 2010 - 10:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I assume you have the Force exhaust?

The O2 sensor is in the WORST position on those pipes. You either need to get creative, get a crows foot wrench or get an offset O2 sensor wrench.
Top of pagePrevious messageNext messageBottom of page Link to this message

Turboglh
Posted on Thursday, May 27, 2010 - 08:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Some heat (ideally a small set of oxy/acetylene torches, but a small propane torch or map gas will work) and some good rust penetrant (mopar makes a good one, and we use aerokroil at work)

Heat around the bung in the header and a bit on the base of the sensor, get it warm to hot and then spray the penetrant on. The heat helps expand the parts, and allows the rp to work it's way into the threads some.

Repeat as much as you feel is necessary, you want to give it time to work it's way in.

Other than that, a GOOD crows foot (cheap ones will just spread), an offset socket like suggested, or I have a modified 7/8" deep socket that I use for just the bike. My normal o2 socket won't clear the head with the bosch sensor.

Good luck.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ebutch
Posted on Thursday, May 27, 2010 - 09:40 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Mine AmPro CR-V, 7/8" #T70016
Top of pagePrevious messageNext messageBottom of page Link to this message

Ebutch
Posted on Thursday, May 27, 2010 - 09:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

3/8" drive most any parts store
Top of pagePrevious messageNext messageBottom of page Link to this message

Ebutch
Posted on Thursday, May 27, 2010 - 09:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I do it on my S3with a 6" and 3" extension,3/8s extension and 3/8s ratchet handle.under frame.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ebutch
Posted on Thursday, May 27, 2010 - 10:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Try Freeze-Off penatrent.But It should come off if installed right with never-seeze
Top of pagePrevious messageNext messageBottom of page Link to this message

Ratbuell
Posted on Thursday, May 27, 2010 - 11:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Just be aware...lots of penetrant, and you may as well buy a new sensor. They don't like chemicals.

Turboglh - should I ask? Have an 86 GLHS project, 87 CSX project, 89 CSX show car, and am working on rebuilding a friends' 91 Spirit R/T : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Bandm
Posted on Friday, May 28, 2010 - 10:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

If clearance is a problem, break the top off the sensor, leaving only the hex, remove pipe, remove sensor, get new a sensor, they're cheap
Top of pagePrevious messageNext messageBottom of page Link to this message

Turboglh
Posted on Friday, May 28, 2010 - 12:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Absolutely a new sensor.

@ratbuell of course, had two turbo glh's, a carbed hi compression 84 and a 87 shelby lancer. All the old cars are gone now, just have the srt4 now.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ratbuell
Posted on Saturday, May 29, 2010 - 01:21 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Ya, used to have an 87 SL leather/auto as well. The R/T I'm rebuilding is one I used to own. Also had a slew of turbo drivers - 89 Spirit ES, couple Daytona Shelby's - and still own the first new car I ever bought, a one-of-150 (total; one of 26 with options) documented '91 Daytona CS/AGS Competition Package car with 74k original miles.

If I have my way, I'll be buried in that car : )
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration