G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Old School Buell » Archive through July 01, 2009 » Brake Issues...DOT3/4/5 « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Andymnelson
Posted on Wednesday, June 24, 2009 - 12:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Ugh, so I put new front pads on my 99 X1...VERY easy job! went to bleed brakes, and top it off...and, sweet, PO put in DOT3 or 4. So I drained the whole system, disassembled the caliper, cleaned everything with DOT 5, blew out the line, filled with DOT 5, reassembled, bled....and no pressure. at all. I can bleed them and push fluid through the line just fine, but I don't build up any pressure in the system.

What do I do next? Get a master cylinder rebuild kit? Caliper rebuild kit? Both? Replace the line while I'm at it?

Dumb....seriously, if it says DOT5, put DOT 5 in!
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Wednesday, June 24, 2009 - 12:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Re-clean system, use DOT 4.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andymnelson
Posted on Wednesday, June 24, 2009 - 12:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Will that really help the problems?
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Wednesday, June 24, 2009 - 12:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

No it will not help with your bleeding problems but will keep you from having others later.

FSM and the top of both reservoirs specify DOT 4.

http://faq.f650.com/FAQs/BRAKEMAINTENANCEFAQ.htm

(Message edited by `J.ramsey on June 24, 2009)

(Message edited by `J.ramsey on June 24, 2009)

(Message edited by `J.ramsey on June 24, 2009)
Top of pagePrevious messageNext messageBottom of page Link to this message

Andymnelson
Posted on Wednesday, June 24, 2009 - 12:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

My FSM and top of both of my reservoirs specify DOT 5...
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Wednesday, June 24, 2009 - 12:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Must have changed to DOT 4 on the '00 and up models.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andymnelson
Posted on Wednesday, June 24, 2009 - 01:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Yeah I'm thinking so.

So what do I do now? I can't imagine the DOT 5 being my issue...
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Wednesday, June 24, 2009 - 01:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Probably air locked, vacuum bleeding is the quickest-easiest way.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andymnelson
Posted on Wednesday, June 24, 2009 - 01:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)



I've bled them for literally 1/2 hour. I feel confident that there is no air in the system.

I have tore apart/cleaned the caliper.
I tore apart/cleaned the master cylinder.
Both looked good- all surfaces clean and smooth and seals were all in good shape. Makes me think that the $50 I would spend on rebuild kits for them would be wasted?
Top of pagePrevious messageNext messageBottom of page Link to this message

12mpghwy
Posted on Wednesday, June 24, 2009 - 05:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

It can be really hard or impossible to hand bleed bike brakes. I spend HOURS trying to do this in the middle of the night when I had to use the bike to ride to work the next day Use a vacuum pump.

Though when I was doing it that time I didn't have hardly any tools I ended up making a chamber out of a peanut butter jar, that is a peanut butter jar with 2 holes drilled in the lid and hoses shoved in so the kind of seal with some kind of silicone or sealant around the lines on the top.

Then hooked up to the idling bikes engine vacuum. This did the bleed that I had been working on for at least 6 hours in less than 30 seconds.

To clarify one of the 2 lines goes into the bikes vac source which draws a vacuum on the jar, the other line goes to the caliper so that the fluid will be rather quickly sucked into and collected in the jar. You have to be ready because this will suck the master cyl dry of fluid in seconds. Obviously close the bleed nipple while vac is still on the system and then it will work.

(Message edited by 12mpghwy on June 24, 2009)
Top of pagePrevious messageNext messageBottom of page Link to this message

Sloppy
Posted on Wednesday, June 24, 2009 - 05:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I find that air will hang out in the banjo bolts. Crack these open under brake pressure a few times (but do make sure you put rags around it at Dot 3,4, 5.1 don't get along with paint).

With a caliper rebuild I also have had to remove the caliper and move it around to get the last residual air out the bleeder.

Note: I don't always get a "strong lever" feeling with the bike standing still (not sure why, perhaps due to the floating rotor?), but it firms up fine on the road. If you're not sure, do a quick jaunt around the corner. Also if the caliper pistons are stuck (you'll have to see all 6 come out evenly) that will also give you a spongy lever.
Top of pagePrevious messageNext messageBottom of page Link to this message

Kalali
Posted on Wednesday, June 24, 2009 - 07:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

'99 X1 = DOT5, '00 X1 = DOT4. This is according to my FSM and is consistent with what is on the reservoir lid.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andymnelson
Posted on Wednesday, June 24, 2009 - 08:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Well seeing as tho DOT5 is silicon based and sticks to everything, and 3/4 are glycol based and tend to strip anything off of everything...I decided to try something and I tore apart the ENTIRE system once again, cleaned it all out, filled er up with DOT4, bled it....and it works just fine now. I'm guessing that the 4 and 5 mixture gunked up somewhere that the 5 would not clean out, but the 4 did.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fullauto
Posted on Thursday, June 25, 2009 - 03:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Al at American Sport Bike said that if you are changing the '99s from Dot 5 to Dot 4 it's a good idea to replace the front brake line when you do it, as well as putting the seal kit through the master cylinder and caliper as it only takes a drop of Dot 5 to form a blob in the system. I've got all the gear to do it and it's on my maintenance list.
Top of pagePrevious messageNext messageBottom of page Link to this message

Kalali
Posted on Thursday, June 25, 2009 - 07:46 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

What I don't understand is the brake components "appear" to be identical between '00 and '99. So how come the fluids are so different?
Top of pagePrevious messageNext messageBottom of page Link to this message

Fullauto
Posted on Thursday, June 25, 2009 - 09:30 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

They are identical. The factory ran Dot 5 for only the one year in X1s and I presume the other models as well.
Top of pagePrevious messageNext messageBottom of page Link to this message

Skntpig
Posted on Thursday, June 25, 2009 - 04:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

You don't want to mix DOT 3/4 with DOT5.

http://www.tccoa.com/brake-fluid/

They are really the same or similar system from year to year, and can take either 3/4 or 5 but you can never switch back and forth.

The seals swell. I found this out first when I trashed my vacuum bleeder. I couldn't see how the o-rings didn't fit anymore. They were literally about double the size.

Once I figured it out it gave me an excuse to buy a radial master. I replaced the line and disassembled and cleaned the caliper with denatured alcohol before rebuilding with new seals.

I figured the brakes are a pretty important thing to have work all the time, every time.
Top of pagePrevious messageNext messageBottom of page Link to this message

Kalali
Posted on Thursday, June 25, 2009 - 08:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

"I figured the brakes are a pretty important thing to have work all the time, every time."

No kidding!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Fullauto
Posted on Thursday, June 25, 2009 - 09:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Let's face it, brakes only slow you down !!
Top of pagePrevious messageNext messageBottom of page Link to this message

Buell_bert
Posted on Thursday, June 25, 2009 - 11:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I don't care if the bike goes fast but the 2 things I want are good tires and good brakes. The rest is just an extra. Safety first.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration