G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Old School Buell » Archive through April 09, 2009 » Good, replacement lifters? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Brinnutz
Posted on Thursday, April 02, 2009 - 01:07 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've been reading around the web lately and am looking for the best lifter replacements.

I hear the 18538-99B's are the best, but do those fit the tubers? I believe they do, but I want to double check.

Also, any how to's on how to properly replace them would be great as well
Top of pagePrevious messageNext messageBottom of page Link to this message

Firemanjim
Posted on Thursday, April 02, 2009 - 02:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Wilson,why are you replacing them? Aftermarket has good ones as well--Jim's work well.
Do you have stock pushrods--if so rocker boxes are coming off,then pushrod tubes and pushrods,lifter pins come out then lifters,fill them with oil before installing new ones.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brinnutz
Posted on Thursday, April 02, 2009 - 02:25 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Just figured I'd replace them while the rockers were off, and replacing the bases with the NRHS ones.
I figured since I can't afford the 1250 now I am going to do as much preventative maintenance, and wear maintenance as possible.
Had a fair amount of ticking coming from up there, so I figured I'd just get them outta the way, if I can afford it.

(Message edited by brinnutz on April 02, 2009)
Top of pagePrevious messageNext messageBottom of page Link to this message

Hootowl
Posted on Thursday, April 02, 2009 - 11:23 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

That ticking is most likely coming from the cams gears, and telegraphing up the pushrods. Your lifters are probably fine.
Top of pagePrevious messageNext messageBottom of page Link to this message

Lovedabueller
Posted on Thursday, April 02, 2009 - 12:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

i have a lot of "ticking" coming from mine also. and its on the topend. especially after things warm up.

any thoughts. can you get different ratio rockers. more power.

keith
Top of pagePrevious messageNext messageBottom of page Link to this message

Sloppy
Posted on Thursday, April 02, 2009 - 03:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If you are interested in preventative maintenance then there are far better options.

Oil gear drive upgrade
Swap to xb rocker covers
Roller rockers
Use synthetic oil
Etc
Top of pagePrevious messageNext messageBottom of page Link to this message

Firemanjim
Posted on Thursday, April 02, 2009 - 03:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

And the newer oil pump with more scavenge capacity.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brinnutz
Posted on Thursday, April 02, 2009 - 04:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ok, just was speaking with Sleez.

The updated oil pump is :

26357-02B OIL PUMP ASSEMBLY

This is not stock on any tubers, correct?

And, does anyone know if that includes the Bronze gear? I thought it did. Thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellsrule
Posted on Thursday, April 02, 2009 - 05:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Probably the best deal on lifters are the ones from Revolution Performance. They sell the V-thunder lifters for a little over 100.00 a set. You can find them cheaper on ebay but I think it's good to try and support a vendor here when you can.

BR
Top of pagePrevious messageNext messageBottom of page Link to this message

Sloppy
Posted on Thursday, April 02, 2009 - 07:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Does not include the alloy gear - you'll need to buy separetely. Also you'll need to transfer the fittings from the tuber oil pump.

Do you have the Factory Service Manual???
Top of pagePrevious messageNext messageBottom of page Link to this message

Brinnutz
Posted on Friday, April 03, 2009 - 09:37 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I do have the FSM, but recently found a discrepancy with it in the wiring, and it f'ed me. I cut my harnesses loom looking for a connector the manual said was there, but it wasn't. Going to call Buell today and see if they will help a broke Bueller out. (See Court's area for the thread).

Anyways, I ordered the Bronze gear last night for like $39, along with some Pro Series X1 fork springs which are obsolete.

Well, as far as the fittings, I am planning on saving for a polished aluminum oil tank from Metamachex.com (You have to email them, but they have them, and it's about $250 less than American Sport Bike from them without shipping from the UK.

So, I plan on adding all stainless steel lines, so I will have to fit the proper fittings when I get them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Lovedabueller
Posted on Friday, April 03, 2009 - 09:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

are you taking pics of all the progress you are doing, cause this is like an episode of overhaulin. PICS MAN PICS.

are you going to keep the bike the same color scheme as before.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brinnutz
Posted on Friday, April 03, 2009 - 10:22 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yeah, umm..not really takin pics.

I guess I could.

But it's going to take a while. I don't have the money to get the motor work done now since I bought some XB heads for cheap.

Well, looks as though I may not have a bike this season, but that's ok. I'll be saving up to get the motor built....
Top of pagePrevious messageNext messageBottom of page Link to this message

Brinnutz
Posted on Friday, April 03, 2009 - 10:27 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Another reason for no pics, is the frame is now in the Attic of the Barn where I'll be doing the extensive cleaning of every nook and cranny.

Swingarm, forks (uppers and lowers), possibly triples, and other odds and ends I plan on getting powdercoated shiny ceramic or the durashine or whatever its called.

And exhaust.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellsrule
Posted on Friday, April 03, 2009 - 10:30 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Wilson, what's the part number for the fork springs. I need a set and want to try and find some. Thanks, Frank.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brinnutz
Posted on Friday, April 03, 2009 - 10:40 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

PM incoming.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration