G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Old School Buell » Archive through February 21, 2009 » Grenade plate gone!!!!!!! but i screwed up....... « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Limitedx1
Posted on Thursday, February 19, 2009 - 07:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

so i got my energy one extra plate kit in my x1 last night. that all went well and without a hitch. as i slide my primary cover back on i line up the shifter shaft and give it a good tap, what do ya know the shifter seal flips inside out as it goes on the shaft because i had already pressed the seal into the cover. so upon trying to remove the seal without damage....waaaaam stuck the screw driver straight through the rubber part of teh seal lol. my question is, was i supposed to wait to press the seal in after i got the cover on? as it sits now i have the thing completely back together and tight minus the shifter shaft seal, i hope i can slide it over the shaft and press it into the case now that its back together.......also is it easiest to run to a dealer and grab that seal rather than order it......

p.s. the energy one 15% spring doesnt seem that much harder to pull if any at all than stock.... havent rode it yet, but the couple of pulls in the garage felt just like stock
Top of pagePrevious messageNext messageBottom of page Link to this message

Jos51700
Posted on Thursday, February 19, 2009 - 08:52 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I always install the seal last, right before reinstalling the shifter. It prevents what happened to you, and also avoids cutting the seal on the splines. Wrap the shifter shaft in electrical tape (Start at the inside, and work outwards) to cover the splines, and protect the seal.
Top of pagePrevious messageNext messageBottom of page Link to this message

Limitedx1
Posted on Thursday, February 19, 2009 - 10:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

perfect, thats what i needed to know!

p.s. i just scored a set of american air cooled big bore 88" cylinders!!!!! the race is on for boring and pistons!!!!! so its all gonna come back apart lol
Top of pagePrevious messageNext messageBottom of page Link to this message

Brinnutz
Posted on Thursday, February 19, 2009 - 10:22 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Where from?
Top of pagePrevious messageNext messageBottom of page Link to this message

Limitedx1
Posted on Thursday, February 19, 2009 - 10:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ebizzzle
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Thursday, February 19, 2009 - 11:37 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Funny, I have had my cover off five times and have never bothered to do anything with it.
Perhaps the dealership replaced it when they did a tranny job top it some years back but I have never done anything at all with it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Limitedx1
Posted on Thursday, February 19, 2009 - 11:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

my gasket kit came with a new one and the spring inside of my stock oil seal was looking kinked, so i put it in before i put the cover back on, well the shift shaft jsut flipped it inside out when i put it back on, so to the store i go for another one and i will install it now that the cover is back on and tight, and not leaking i might add!!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Big_koch
Posted on Thursday, February 19, 2009 - 02:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Just reinstalled mine last night also, ironically enough. A 1/2" or 9/16" deep socket (can't remember which...smallest which will fit over the shaft) worked well to press the seal back into the cover.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration