G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Old School Buell » Archive through February 03, 2009 » Exhaust Gasket Question « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Rabert
Posted on Monday, January 19, 2009 - 09:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Took my exhaust header off and noticed that there was no gasket. It appeared that the gasket, I think, is embedded into the exhaust port. I suspect that it has attached itself since this is the first time it has been off the bike. My question is before I start scraping, should the exhaust port be clean and down to bare metal? Or am I removing something I shouldn't? Kinda looks like an "SOS pad gasket".....know what I mean? Thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Preybird1
Posted on Monday, January 19, 2009 - 09:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yes its a metal mesh gasket, just pluck/pick away. You will get down to a nice little seat for the new ones. There just smashed in there.
Top of pagePrevious messageNext messageBottom of page Link to this message

Rabert
Posted on Monday, January 19, 2009 - 09:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks, I shall commence to pluckin.....
Top of pagePrevious messageNext messageBottom of page Link to this message

Preybird1
Posted on Monday, January 19, 2009 - 10:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Oh save yourself some time at the dealer and just order the evo sportster gaskets there the same thing.

Now dont mention that these are for a buell or you will just confuse the poor parts guy and he may treat you different,Ah hell just say it and watch the fanfare commence
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Monday, January 19, 2009 - 10:13 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

GASKET,exhaust port PN 17048-98 is the one to get !!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Monday, January 19, 2009 - 11:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Put the new ones in the freezer to shrink them a bit before installing them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Texastechx1
Posted on Tuesday, January 20, 2009 - 12:40 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

hey buellistic, whats the difference between parts?
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Tuesday, January 20, 2009 - 09:20 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

GASKET,exhaust port PN 65324-83A is no good as it squeezes into the port, plus it is not easy to install ...

Gasket,exhaust port PN 17048-98 is much easier to install and can be turned over and reused ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldironsides
Posted on Tuesday, January 20, 2009 - 09:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Is that prt# good for an 01 x1. And is there a retaining ring that holds the gasket in? A breakdown I have shows a retaining ring. Thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Tuesday, January 20, 2009 - 09:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The retaining ring goes on the pipe and gives the clamp something to hold so it can mash the pipe into the head.
Nothing keeps the gasket thingy in there other than the pipe being mashed in there.
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldironsides
Posted on Tuesday, January 20, 2009 - 10:47 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Appreciate the info Nate. Do you know if the part prt#s' good for my bike. I dont have a prts' manual yet. Thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Tuesday, January 20, 2009 - 04:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

UP-DATE to my post Tuesay,January 20,2009!!

PN 65324-83A is now "-83B" and one per package sells for $7.13 ea ...

PN 17048-98 comes two in a package and sells for $9.07 ...

Not only are the PN 17048-98 better they are also cheaper !!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Tuesday, January 20, 2009 - 04:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks Buellistic, I wrote that in my parts books for future reference.
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Tuesday, January 20, 2009 - 07:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So what does the good one look like before install?
The ones I put in last were like the lower corner of a cylinder. You know, like a funnel inside?
If I have the "bad ones" I won't go in there but I'm just a bit curious.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Tuesday, January 20, 2009 - 07:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Natexlh1000:

Glad you ask'ed that ...

The good PN 17048-98 are thin and fit perfectly in the exhaust port notch which you must make sure is clean before inserting the new one in ...

These are so good that "i" turned them over and reused ...

"BUT" like installing, removing one to turn over you must be careful ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Billetmetallic
Posted on Tuesday, January 20, 2009 - 09:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Buellistic, I must give you props here, you are always helping out anyone who asks, and in more than timely fashion, I thank you for it, so should everyone

thanks again!

-g
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Tuesday, January 20, 2009 - 10:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Billetmetallic:

The one's that taught the one's the taught the one's that taught me and "i" am just passing it all on ...

In BUELLing
LaFayette
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldironsides
Posted on Wednesday, January 21, 2009 - 09:04 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Buellistic

Is the 17048-98 The right gasket for a 01 X1. I do not have a parts manual yet. And I want to be able to just give the dealer the # cause my local dealer doesn't like Buells. Thanks in advance
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Wednesday, January 21, 2009 - 09:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Oldironsides:

This PN 17048-98 fits all EVO SPORTSTER engines(what is in the tube frame BUELLS), BLAST, XB, and even BIG TWINS ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldironsides
Posted on Wednesday, January 21, 2009 - 11:11 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Buellistic

Thankyou Sir and sorry for the ignorance. Still in training please be patient. I appreciate the timely reply
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Wednesday, January 21, 2009 - 11:32 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Oldironsides:

The one's that taught the one's that taught the one's that taught me and now "i" am just passing it all on !!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Kyrocket
Posted on Wednesday, January 21, 2009 - 01:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yeah, Buellistic is pretty good 'til he vaporlocks on the side of the road and scares the bejesus out of you thinking something bad has happened.

Just giving you crap, how many miles have you logged so far? And any plans to make it back to the bluegrass state?
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Wednesday, January 21, 2009 - 01:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Kyrocket:

106,551.0 miles as of the last ride ...

Have a ex-husdand inlaw(wife's ex)about to pass away, so it could be any time really ... Will be there for the girls(3)... Will probable get to stay a while, so the bike comes too ... Will e-mail everyone on the Kentucky BUELL Riders E-MAIL LIST for a Ride if possible ...

In BUELLing
LaFayette
Top of pagePrevious messageNext messageBottom of page Link to this message

Rabert
Posted on Thursday, January 22, 2009 - 01:44 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Wow I thought this thread had died as I haven't been here in awhile. I really..really....really appreciate the comments. This is a great forum! Decided to do my fork seals and intake seals too. Any comments on these?
Top of pagePrevious messageNext messageBottom of page Link to this message

Eboos
Posted on Thursday, January 22, 2009 - 03:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I love the technical terminology being used here...

Mashed and smashed... with character like this why would you want to ride any other brand.
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Thursday, January 22, 2009 - 03:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Rabert dig through the KV I did an extensive tear down of the forks and was delighted when Goingwindward added the XB info to the basic procedure,

My two thoughts,
have all of the pieces before you start, and cleanliness is every thing, the assembley except for driving the seals is straight forward.

Intake seals skip the coffee that morning or at least limit it
look through the KV and ask here I ahve done them its straight forward.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration