G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Old School Buell » Archives OSB 001 » Archive through April 01, 2007 » Questions about M2 tank. « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Rum_runner
Posted on Friday, March 23, 2007 - 06:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I bought a M2 tank for the S1. Will the Gas cap and chrome ring from the S1 tank fit the M2 tank.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sleez
Posted on Friday, March 23, 2007 - 06:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

as far as i know, they will. i have used a number of different tanks with different caps/rings, all work fine.

note, all the keyed caps that were on S3s are keyed alike. as far as i have seen, the many i have tried will all open with any key.
Top of pagePrevious messageNext messageBottom of page Link to this message

Eshardball
Posted on Sunday, March 25, 2007 - 01:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ditto. I put the M2 tank on my S1. Used the ring, cap & petcock from the S1. Had to have risers made for my Crossroads bars to clear the tank though.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sanchez
Posted on Sunday, March 25, 2007 - 01:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yep, the cap, ring, and petcock transfer. The screws that hold the petcock in are different though (and vary from year to year of M2, even). I don't remember the size off hand, but it's in the parts book.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ratbuell
Posted on Sunday, March 25, 2007 - 07:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If you put a bigger (Manta) M2 tank on an S1, you should be able to use the S1W Crossroads bars - the S1W came with the larger tank from the factory. Doublecheck with Al at American Sport Bike though....
Top of pagePrevious messageNext messageBottom of page Link to this message

Littlebuggles
Posted on Monday, March 26, 2007 - 05:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I use the S1W crossroads bars on my bike. The exterior of the tank is the same on S1W, S3(T), and M2. Now using a 98 S3T tank, previously had my original M2 tank on. No clearance probs.

-Mike
Top of pagePrevious messageNext messageBottom of page Link to this message

Spiderman
Posted on Monday, March 26, 2007 - 07:34 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The ring and cap are the same, however the S1 tank has different screws than the manta tank.
Top of pagePrevious messageNext messageBottom of page Link to this message

Djkaplan
Posted on Monday, March 26, 2007 - 08:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The little rubber splash guard will shrink (dessicate?) if you take it out and don't put it back in right away. I had so much trouble getting it back on after painting my tank, I bought another one. It was still a tight fit until the new one was re-plialized by fuel vapor.

I just made that word up, btw.
Top of pagePrevious messageNext messageBottom of page Link to this message

Littlebuggles
Posted on Tuesday, March 27, 2007 - 01:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

re-what?

Those splash guard things are an absolute pain, I also had trouble with mine. Also had to loosen the locknut on the bottom of the gas cap to get the locking tab to flip down. Tightened it up later for a good seal once the rubber had been exposed to gas and re-plialized.




Oh yeah, if you replace the breather line for the gas tank make sure the line is big enough. I bought two different diameter lines and had to change to the larger when the bike stalled out several times, starving for fuel. Maybe that's common sense but the line shrinks due to the exposure to vapors and made it hard to tell what size was correct.


Any English majors that can tell us how many words Shakespeare(sp?) added to the dictionary?
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration