G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Old School Buell » Archives OSB 001 » Archive through December 21, 2006 » Fork seals « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Rum_runner
Posted on Sunday, October 08, 2006 - 08:25 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

what is the life on fork seals blew mine out today. kinda wondering if there eas some thing wrong with them or it they were just old.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mbsween
Posted on Sunday, October 08, 2006 - 08:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

My 01 X1 has 33,000 on the stock fork seals, no weeping yet
Top of pagePrevious messageNext messageBottom of page Link to this message

89rs1200
Posted on Monday, October 09, 2006 - 12:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Had an S3 Right side that went out about 25,000. Right sides weep more than the left. Be sure to check and wipe down the dist before each ride. Dust on the fork tube takes them out faster than anything else I can figure.

(Message edited by 89rs1200 on October 09, 2006)
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Monday, October 09, 2006 - 06:41 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

On another thread, someone posted a trick:

Take a tearoff or some other piece of very thin plasic.
Cut a shallow hook into it and insert the tool up between the slider and the seal.
The idea is to pull out any dust or other crap that might be in there.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sloppy
Posted on Monday, October 09, 2006 - 02:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

You can pull down the dust cover and clean up under the seal.

I found that insects would be the cause of frequent fork seal leaks, so I wipe down the "male" forks with silicone spray and pull down the dust cover monthly during "insect season". I haven't had a blown fork seal in 20,000 miles since I started this procedure.
Top of pagePrevious messageNext messageBottom of page Link to this message

Krusty
Posted on Monday, November 13, 2006 - 08:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

> [I've had 2 sets in my X1 over the last few years. Hard riding, wheelies, > rough roads. Most Buells get a caning]
Top of pagePrevious messageNext messageBottom of page Link to this message

Fuelledbuelled
Posted on Sunday, November 26, 2006 - 11:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If you leave the bike sitting for months the fork seals can go hard and perish. My 98 S3 had very low miles from the previous owner, which contributed to the right side leaking.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tbolt_pilot
Posted on Monday, November 27, 2006 - 12:06 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ditto on that. Exact same bike and situation as mine. My advice, make it a habit of wiping the tubes down before riding and at gas stops, etc. You know...bugs!
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration