G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Knowledge Vault (tech, parts, apparel, & accessories topics) » Electrical - Battery, Charg Sys, Lights, Switches, Sensors & Guages » Does anyone know the proper coating used for stators? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Ceejay
Posted on Wednesday, August 30, 2017 - 08:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Hello, I purchased an upgraded stator rotor combo, but it had a small nick in the coating which I'd like to fix prior to install. Does anyone know the proper coating? Thanks in advance.
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Thursday, August 31, 2017 - 04:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The epoxy on holding the wire in place or the actual wire coating? The wire does have it's own coating.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ceejay
Posted on Thursday, August 31, 2017 - 08:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Hi Terry,
The chip is actually on one of the pole parts. So I'm guessing it's the epoxy coating - is that a specific epoxy type?
Thanks, Corey
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Thursday, August 31, 2017 - 09:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The epoxy is only really there to prevent movement/vibration. It will need to be oil resistant and handle 250-280 heat. JB Weld make some good for 300.
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Thursday, August 31, 2017 - 09:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The hard part will be getting it to stick to the existing epoxy.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Friday, September 01, 2017 - 03:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

What about just patching the chip with some good RTV after very careful cleaning?
Top of pagePrevious messageNext messageBottom of page Link to this message

Ocbueller
Posted on Friday, September 01, 2017 - 05:48 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

A product called Glyptol strikes my memory.
But my memory ain't that great.
SteveH
Top of pagePrevious messageNext messageBottom of page Link to this message

Brother_in_buells
Posted on Saturday, September 02, 2017 - 08:02 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The coating on the copper wires are something like schellac.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ceejay
Posted on Saturday, September 02, 2017 - 04:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Reep - that sounds like a great idea actually. Then if it does peel or fall off it wont cause much additional issues either. I was worried about JB weld thinking it was sintered metal (which may not be true) and I've read about glyptal before though I have no clue what it is or where to get it...
Top of pagePrevious messageNext messageBottom of page Link to this message

Ocbueller
Posted on Saturday, September 02, 2017 - 04:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I googled Glyptal, available from CRC, Eastwood etc... , insulating enamel paint. Used on electrical windings.
SteveH
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration