G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Archive through February 18, 2017 » Throttle housing slipping on Renthals « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Gregoxb
Posted on Saturday, September 10, 2016 - 03:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I installed a new set of Renthal handlebars. The throttle housing rotates when some force is applied. Is there a way to get it to fit more snug?

(Message edited by gregoxb on September 10, 2016)
Top of pagePrevious messageNext messageBottom of page Link to this message

Brother_in_buells
Posted on Saturday, September 10, 2016 - 03:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Use a little bit of isolation tape on the clamping area!
Top of pagePrevious messageNext messageBottom of page Link to this message

Gregoxb
Posted on Saturday, September 10, 2016 - 06:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Cool, I'll try that. Thanks.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brother_in_buells
Posted on Sunday, September 11, 2016 - 04:41 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I did the same with the lsl handle bar ,one or two rounds with some thin electric isolation tape.
And when the housing is mounted it is not or almost not visible ,you can cut the visible piece away with a razor or stanley knife.
Top of pagePrevious messageNext messageBottom of page Link to this message

Teeps
Posted on Sunday, September 11, 2016 - 12:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I used "servo mounting tape."

http://www.hobbylinc.com/rc-airplane-servo-tape
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Monday, September 12, 2016 - 09:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

You could also shave a bit of the clamping surface with a flat file. Probably less than 1mm
Top of pagePrevious messageNext messageBottom of page Link to this message

Doz
Posted on Monday, September 12, 2016 - 11:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I cant remember but isn't there a "pin" in the housing and you have to drill a hole in the bar for it to fit into?
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Tuesday, September 13, 2016 - 10:15 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The pin and hole is for the switches.
I don't think anything on the twistgrip other than friction.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration