G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » XBoard » Archive through March 27, 2015 » What is this nipply thingy « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Spag
Posted on Tuesday, January 27, 2015 - 09:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Hi, this is my first post here. I'm a new buell owner and learning the hard way about fouling plug issues. I have an 03 firebolt xb9r and I guess I blipped the throttle to much while riding in town. When I stopped it wouldn't start back up. Also a plug wire was loose on the box and the other wire was corroded where it attaches to the plug. So I think I found the problem. Need to replace the plugs and plug wires. But I discovered this nipple while looking around under the air box. Nothing is connected to it and I can't find anything to connect to it or any other place not connected. Any ideas what it is? I have ridden the bike about 400 miles since I got it last week. It has ran perfect until it wouldn't start. I cleaned the plugs but it's running like crap right now... Waiting to get plugs an wires this weekend




Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Tuesday, January 27, 2015 - 11:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Something that needs to be capped! I forget what size I used, but I spun a tap down in there and put a set screw in because I kept losing the rubber vacuum caps.

(Message edited by greg_e on January 27, 2015)
Top of pagePrevious messageNext messageBottom of page Link to this message

Cobra66
Posted on Wednesday, January 28, 2015 - 12:39 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'm not exactly sure. But it may be a port to test the fuel injection. I know cars have them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Cobra66
Posted on Wednesday, January 28, 2015 - 12:40 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

if that's the case it doesn't connect to anything. just put a vacuum cap over it to keep the valve clean.
Top of pagePrevious messageNext messageBottom of page Link to this message

Nillaice
Posted on Wednesday, January 28, 2015 - 12:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I think It's for the emissions canister.

So, yeah ... Cap it
Top of pagePrevious messageNext messageBottom of page Link to this message

M1combat
Posted on Wednesday, January 28, 2015 - 04:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Cap it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Wednesday, January 28, 2015 - 08:27 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Mine lost that cap also. I put a short length of tubing on it with two cable ties (one to hold it on the post, a second to squeeze the end of the tube shut).

I might have stuffed a small screw in the end of the tube as well to plug it, I can't recall.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hogs
Posted on Wednesday, January 28, 2015 - 08:47 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Some had said since this is either before or after the Butterfly say that it really does Not matter if its capped off or not???
Top of pagePrevious messageNext messageBottom of page Link to this message

Doz
Posted on Wednesday, January 28, 2015 - 08:49 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

And stop blipping the throttle
Top of pagePrevious messageNext messageBottom of page Link to this message

No_rice
Posted on Wednesday, January 28, 2015 - 11:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

they came with no cap... if i remember right it may not even pass completely into the throttlebody. although i havent paid attention to it for years.

and yes quit blipping the throttle, your on a buell!
Top of pagePrevious messageNext messageBottom of page Link to this message

Teeps
Posted on Wednesday, January 28, 2015 - 12:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

That nipple is a "ported vacuum" source Calif evaporative emissions.
The passage in the throttle body is just above the throttle plate in the closed position.
When you crack the throttle. A small vacuum is present at this port. This weak vacuum is connected to the charcoal canister, so as to vacuum the unburned fuel vapors and keep the canister dry inside so the activated charcoal can do its job.

This port is unfiltered and should be capped. However, if left uncapped and unfiltered, it will likely plug with debris sooner than later. Thus effectively capping the passage solving the to cap or not to cap dilemma.
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Wednesday, January 28, 2015 - 01:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Teeps' post is correct.

The cap easily comes off, hence why they are often missing.
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Wednesday, January 28, 2015 - 07:48 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It might have been a 10-32 tap and set screw that I used, either that or a 4-40 since I can't remember the diameter of that port. All I remember was thinking how nice it was that I had both a tap close enough to work, and a set screw to turn down inside to plug it.

The more I think about it, the more I think 4-40 is the size I used, the 10-32 was a different port I put in downstream with the hope of someday building a ram air intake and adding the manifold pressure sensor and programming the ecm for the change.
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Thursday, January 29, 2015 - 02:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Wouldn't a little blob of silicone or epoxy be better than one of those caps that pop off so easily?
Top of pagePrevious messageNext messageBottom of page Link to this message

Spag
Posted on Thursday, January 29, 2015 - 10:34 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks for all the info... I'll go ahead and cap it. I did put a small hose on it and blew into it, it was not plugged off yet and air did come through it and out the throttle body...

trust me I learned my lesson about blipping the throttle.
Top of pagePrevious messageNext messageBottom of page Link to this message

Nobuell
Posted on Friday, January 30, 2015 - 04:13 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Magnecor makes a nice set of 8 mm plug wires for the bike.
Top of pagePrevious messageNext messageBottom of page Link to this message

Spag
Posted on Friday, January 30, 2015 - 09:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks, I'll check into it
Top of pagePrevious messageNext messageBottom of page Link to this message

Djohnk
Posted on Tuesday, February 03, 2015 - 02:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I also lost a few rubber caps ... ended up plugging it with jb weld. Its lasted for a couple years now with no problem
Top of pagePrevious messageNext messageBottom of page Link to this message

Firemanjim
Posted on Tuesday, February 03, 2015 - 03:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It is a vacuum source for the charcoal cannister, not meant to be open. Plug it!
Top of pagePrevious messageNext messageBottom of page Link to this message

Spag
Posted on Wednesday, February 04, 2015 - 11:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks a lot for the info
Top of pagePrevious messageNext messageBottom of page Link to this message

Unlucky1
Posted on Thursday, February 19, 2015 - 11:47 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

My PO loaded that up with blue RTV.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration