G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » XBoard » Archive through October 19, 2013 » Fixing Plastics « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Sifo
Posted on Saturday, August 24, 2013 - 06:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So a few years back the chin fairing on my XB gave in to vibration, I believe due to not having any support at the front with the Jardine mount. Here's a pic I posted of it way back when...





So today, I looked up how to weld plastics up on Youtube. There's plenty of videos, I'll let you look for them if you have interest. I just wanted to share my experience of doing this for the first time. It's pretty easy to do. I used some plastic from a 5 gallon paint bucket as filler on the inside to build up a bead to strengthen the repair. I'm not really sure how similar this is to the Buell plastics, but it seemed to work very similarly, and seemed to mix together when melted, so I'm hoping for the best. A better filler would be a piece of plastic from a "donor" piece, but this was a no investment trial.

Here's my results, inside...





And out...





It seems pretty solid at this point. I threw it on the bike to test it for a while. If it holds up, I'll put more time into it and refinish it properly.
Top of pagePrevious messageNext messageBottom of page Link to this message

Slaughter
Posted on Saturday, August 24, 2013 - 09:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

What did you use for a heat source?

I've seen cone-like attachments used on heat guns that make it almost like gas welding.

I tried (and failed) using a soldering iron to try to fix a crack in a plastic trash can.

Curious to see how it holds up. Good idea to "Test" ride it before finish painting.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sifo
Posted on Saturday, August 24, 2013 - 10:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I used a soldering iron. I guess I'll post up the videos that gave me the general idea of how to do it.





It does kind of remind me of gas welding, but it's real easy to go back and smooth things out with another pass. You don't work with a puddle though. It's more of a goo ball. To be honest, I watched the videos without sound, so I have no clue what tips he may give in the audio.

I plan to leave it go for quite a while of riding. If it holds up, I'll finish it this winter. I would really like to fabricate a bracket that would support the front like the stock muffler does. If it fails while this thread is active, I'll be sure to post the update.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sifo
Posted on Saturday, August 24, 2013 - 10:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

BTW, I did find that just like with welding, you need to get some penetration into the original plastic. You can't just melt the filler onto the surface of the original. It will peal right off. Just work very small sections at a time, and know that you can smooth it out with another pass of the iron.

I was also surprised that the iron didn't become a mess with burnt plastic residue.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andersonhdj
Posted on Sunday, August 25, 2013 - 10:19 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I do this slightly differently!

I use a small section of stainless strainer screen which i then heat and embed into the plastic , slightly below the level of the normal surface , thereafter the plastic is welded by adding some donor material and the repair smoothed over.

It takes a little longer but the repair is immensely strong.

I use a small 50 watt temperature controlled soldering iron for the job
Top of pagePrevious messageNext messageBottom of page Link to this message

Absurded
Posted on Sunday, August 25, 2013 - 10:45 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Along the same lines as this thread..but different body part..?? Anyone know of any techniques or products for polishing fine scratches out of a clear firebolt windscreen??
Top of pagePrevious messageNext messageBottom of page Link to this message

Sifo
Posted on Sunday, August 25, 2013 - 08:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Good idea with the stainless screen. Where do you source it from?
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Sunday, August 25, 2013 - 08:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Novus #3 followed by Novus #2 followed by Novus #1 works fine but you need a cloth that will not scratch!
Top of pagePrevious messageNext messageBottom of page Link to this message

Andersonhdj
Posted on Monday, August 26, 2013 - 04:23 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)


quote:

Good idea with the stainless screen. Where do you source it from?




I am in South Africa , so might not be of much help but if i remember correctly , it was an Industrial Company that dealt in Stainless Dairy materials and the like.

Fortunately a small piece 12" x 12" goes a very long way !

You could try a kitchen spatter screen , as used to eliminate oil spatter when frying , Chinese made , it's likely to be a cheaper grade stainless.

Or perhaps a rice strainer?

Probably find one in a Dollar store or the like's of Walmart??
Top of pagePrevious messageNext messageBottom of page Link to this message

Sifo
Posted on Monday, August 26, 2013 - 09:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Great ideas on re-purposing materials. I'm always amazed when I find materials for some project more cheaply in a finished product than I can buy the raw materials by them selves.

I was just thinking that you can often find window screens in a wire mesh. That should work too.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andersonhdj
Posted on Monday, August 26, 2013 - 10:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It's great fun being able to re-purpose things!

I had some fun making headlights for my Lotus 7 rep out of trashcan lids , in stainless. Nobody could figure it out!

Window screens may work but you need a fairly rigid material.

One can also find aluminium mesh used for body repairs here but the stainless is used specifically because it has a degree of rigidity .

When the repair is done , basically the whole section is embedded quickly and completely by forcing first the centre across the crack , then left , then right of it , in quick order while the area is still "Plastic".

It also helps to preheat the mesh so that it goes in easily allowing the molten plastic to ooze through as its pressed in.

The stainless does'nt bend unless it's pre-bent, to fix an angular section

The mesh is used in small sections , cut to roughly 10mm wide by 15 to 20mm long and one would normally set patches about 25 to 30mm apart along the length of a long crack.

Bigger pieces can be used to fuse multiple pieces together as well but obviously takes more effort and a lot of heat , it's a great way to repair really broken fairings and the like.

Unfortunately , i don't have any pics of the process at the moment , usually done for customers or on a rebuild , will post some when i repair my XB's chin spoiler.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sifo
Posted on Saturday, August 31, 2013 - 12:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So my repair has cracked again already. No big deal, it was a zero dollar fix. I'll probably try it again with some sort of stainless steel mesh to reinforce it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Andersonhdj
Posted on Sunday, September 01, 2013 - 07:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Sorry to hear that!

That was the original reason for going the stainless mesh route.

I learned the hard way by using a local plastics repair co to have some scooter panels repaired , the mounting points they were supposed to re-instate were'nt in the correct place and when it came to mounting the cracks they had repaired just cracked wide open again.

That was the last time i ever used a repair company again , learned to do it myself using the method described and never looked back.

There's also another dodge using cyanoacrylate glue if you're interested , but it can be nasty to work , having said that no worse than molten plastic!
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration