G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » XBoard » Archive through October 10, 2010 » Anyone needing larger fuel injectors???? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Ericz
Posted on Saturday, September 18, 2010 - 08:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I just came across these badass direct replacement high flow fuel injectors for XBs. They are 60lb/hr and they drop right in to the XB manifolds!!!!! I was using injectors from the V-Rod Destroyer which flow about 47lb/hr and I had to modify the injector bosses to accept the slightly lower electrical connector on the injector. These Siemens Deka 60lb/hr have the exact same body as the stock XB injectors and they flow more than twice as much!!! These would really only work for a motor with some serious hp as they will support over 215hp naturally aspirated using stock fuel pressure and over 205hp forced induction running 58psi fuel pressure!!!! Yay!!!!

Here is a link to the supplier that just ordered them from: http://www.bmotorsports.com/shop/product_info.php/ cPath/144_146/products_id/449

I am installing some forged pistons and cranking up the boost some more to try to see 200hp
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Saturday, September 18, 2010 - 08:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Equivalent Part Numbers:

* Siemens FI114962 or 107-962 ( 107962 )
* Mototron INJ-GAS-002 ( S107)
* Accel 74620S
* MSD / Edge 2030



Do they fit the stock fuel rail too?
Top of pagePrevious messageNext messageBottom of page Link to this message

Ericz
Posted on Saturday, September 18, 2010 - 09:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yes they do. They are exactly the same as the stock XB injectors except they flow more and have a different spray pattern.
Top of pagePrevious messageNext messageBottom of page Link to this message

Swordsman
Posted on Monday, September 20, 2010 - 12:28 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Don't the XBs just use Ford injectors? I would think that there would be several performance injectors to choose from.
Top of pagePrevious messageNext messageBottom of page Link to this message

Migs16
Posted on Monday, September 20, 2010 - 01:26 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

u cant put these on a stock engine right?
Top of pagePrevious messageNext messageBottom of page Link to this message

Ericz
Posted on Monday, September 20, 2010 - 10:34 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ford uses several different styles of fuel injectors so I'm not sure that you could classify them like that. Most of the performance injectors for Ford cars like Mustangs are much too large and don't fit.

The stock XB injectors have specific front and rear spray patterns that are angled towards the intake valves.

You can use these in a stock engine but there would be no reason to as the stock injectors can provide plenty of fuel for even modified engines. Using larger injectors only is necessary when the stock injectors have to stay open too long to provide enough fuel during the intake cycle. The electronic solenoid in the injector can overheat and the spray pattern and injection timing can suffer if the injector's duty cycle is greater than around 80-85%.
Top of pagePrevious messageNext messageBottom of page Link to this message

Porn_star
Posted on Tuesday, September 21, 2010 - 12:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Will those be right for a 90ci big bore kit
Top of pagePrevious messageNext messageBottom of page Link to this message

Ericz
Posted on Tuesday, September 21, 2010 - 03:10 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It depends on what is put into the 90ci engine and what kind of hp you expect to see. There are several websites that have basic calculators to estimate injector size based on your engine. www.rceng.com has one that is clearly explained. That will give you a good approximation to start with.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ericz
Posted on Tuesday, October 05, 2010 - 09:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Here is a link to a video I just took of the intake manifold and various injectors including the new 60lb/hr ones.

http://www.youtube.com/watch?v=X-rnDxBX5xc
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Tuesday, October 05, 2010 - 10:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The Vrod injectors look pretty, but those Siemens injectors certainly are the correct part, no big guess who makes the stock injectors now.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ericz
Posted on Wednesday, October 06, 2010 - 09:34 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ya, the stock injectors are made by Siemens/Deka. You can see their logo molded into the injector body.
Top of pagePrevious messageNext messageBottom of page Link to this message

96s2t
Posted on Monday, May 30, 2016 - 12:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I thought PT cruiser injectors and the larger turbo PT cruiser injectors where the larger direct replacements for the XB12X?
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration