G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » XBoard » Archive through August 23, 2010 » New Rotor Old Pads? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Jraice
Posted on Thursday, August 12, 2010 - 08:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Is it a big problem to use used pads with a new rotor?
Top of pagePrevious messageNext messageBottom of page Link to this message

Glitch
Posted on Thursday, August 12, 2010 - 09:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

How long do you want the new rotor to last?
Top of pagePrevious messageNext messageBottom of page Link to this message

Hulagun
Posted on Thursday, August 12, 2010 - 09:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Are you that broke, too?

IF the old pads have lots of life left, and IF you like how they have been performing, then just sand the faces (enough to break the glaze off) with 100 grit sandpaper and reinstall them. They should break in like new pads.
Top of pagePrevious messageNext messageBottom of page Link to this message

Dfishman
Posted on Thursday, August 12, 2010 - 10:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I have done the sandpaper trick before.lay your sandpaper on some glass or other real flat surface.I used a figure 8 motion.After a little use the pads break in again to the new rotor.And yes some of us are that broke,or saving up for a 3 week mountain ride.hehe
Top of pagePrevious messageNext messageBottom of page Link to this message

Jraice
Posted on Thursday, August 12, 2010 - 10:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I can afford pads but I JUST installed some ebc hh pads and will be doing a 800 mile road trip on them this weekend but it will be a mellow one so they will still be fresh. I won't be able to ride after that until my October track weekend (moving for school) and I might get the 5mm finned rotor for that but would rather not replace brand new pads
Top of pagePrevious messageNext messageBottom of page Link to this message

Sloppy
Posted on Saturday, August 14, 2010 - 02:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

As long as your pads are not heavily grooved it will work fine.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ourdee
Posted on Saturday, August 14, 2010 - 05:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

+1 on laying the sand paper on a piece of glass.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fast1075
Posted on Sunday, August 15, 2010 - 05:03 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

+2 on the glass....poor man's surface plate.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jraice
Posted on Sunday, August 15, 2010 - 04:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

How much can rotors effect braking force? My rotor has 4 pads worth of wear... All in only 12,500 miles. There is a small ridge in edges from where pads don't touch and also seems to have some other ridges almost too small to feel, where pads so touch. Braking force is way down new pads and cleaned rotor helped some but not enough. Thinking about the 5mm rotor from ebr with their new mounting hardware.

Basically can a worn rotor cause significant performance loss?
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Sunday, August 15, 2010 - 10:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

A worn rotor can cause excessive heat in the braking system. The 5mm rotor is a good choice because the thicker rotor dissipates heat better.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jraice
Posted on Sunday, August 15, 2010 - 10:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I thought the 6mm rotor was the thicker one? Whats the thickness of the OEM rotor? I thought the 5mm just had better cooling based on its shape.

I doubt thats the issue though, brakes arent any better on the first pull than when they are hot (although the rotor does get REALLY hot after a few hard stops, not sure if its normal to be hot enough to burn you).

I am talking about performance loss like first time use for a ride it just wont have much bite/stopping power. Well either way I'll be tossing the 5mm rotor and new Erik Buell Racing hardware on, just hoping this makes the brakes how I hope for them to be (closer to when the bike was new)

The stock rotor looks really beat up.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Monday, August 16, 2010 - 01:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Do a thorough bleed and fluid change as well. That can make a huge difference.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jraice
Posted on Monday, August 16, 2010 - 01:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Already did.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration