G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » XBoard » Archive through August 23, 2010 » Firebolt Grip Removal « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Firebolt_man09
Posted on Thursday, August 05, 2010 - 08:44 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Can anyone tell me how to take the grips off a firebolt.

Thank you
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Thursday, August 05, 2010 - 09:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I use a long skinny flat blade screwdriver.

Pull the plug or bar end and carefully work the blade between the grip and bar/throttle tube then squirt WD-40 in the opening then work the screwdriver blade around the bar.
Top of pagePrevious messageNext messageBottom of page Link to this message

Spiderman
Posted on Thursday, August 05, 2010 - 09:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Are they heated grips? If so the clutch side is screwed on...
Top of pagePrevious messageNext messageBottom of page Link to this message

Glitch
Posted on Thursday, August 05, 2010 - 09:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I use a sharp knife, I don't have heat in my grips
Top of pagePrevious messageNext messageBottom of page Link to this message

Vospertw
Posted on Thursday, August 05, 2010 - 11:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Firebolt, haven't done it on your bike before, but this has worked on others - heat them up a bit with a heat gun/hair dryer (carefully!) and then shoot some compressed air under the grip. Once it's loose, you can start to wiggle it off as you hit it with air.
Top of pagePrevious messageNext messageBottom of page Link to this message

Iman501
Posted on Thursday, August 05, 2010 - 11:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

heck i just took a razor blade to it and cut my right one off since i didnt need it i replaced it to match the left one
Top of pagePrevious messageNext messageBottom of page Link to this message

Jbolt
Posted on Friday, August 06, 2010 - 06:04 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I agree with the kid. If your replacing them, cut'em off.
Top of pagePrevious messageNext messageBottom of page Link to this message

Delta_one
Posted on Sunday, August 08, 2010 - 04:22 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

yup cut 'em off

last season I was going through a set of grips every month, needless to say I stopped using glue too. I still have bits of grip on there and its a pain to get the new grip over the bits of glue and rubber that I couldn't get off, I work at it each time I swap grips but there is still enough to cause a wrestling match when I put my grip on the clutch side.
windex is what I use to help lubricate the grip when I slide it onto the bar and throttle tube but some use hairspray because it acts like a glue when it dries but comes of easily.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brightbuell
Posted on Sunday, August 08, 2010 - 03:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

You can also use rubbing alcohol to lube new grips for putting them on. Once it dries there is no soap or slippery chemicals left behind. SMART!
Top of pagePrevious messageNext messageBottom of page Link to this message

Radioelasais
Posted on Sunday, August 08, 2010 - 07:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I got rizomas. You just slip them onto the bars and secure them with a screw (which I lost riding today ...)
Top of pagePrevious messageNext messageBottom of page Link to this message

Dancing_dogs
Posted on Friday, August 13, 2010 - 10:25 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Locktite that screw on the Rizomas......
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration