G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » XBoard » Buell XBoard Archives » Archive through November 23, 2009 » Frame Puck Removal? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Jonnyrotton
Posted on Saturday, November 21, 2009 - 02:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Anyone have a tried and true method for removing frame pucks?
Top of pagePrevious messageNext messageBottom of page Link to this message

Brother_in_buells
Posted on Saturday, November 21, 2009 - 03:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Just start somewhere were it is easiest,
And this is what you get!
You can try it with spraying some brake cleaner on it maybe that works better??



Top of pagePrevious messageNext messageBottom of page Link to this message

Donniej
Posted on Saturday, November 21, 2009 - 04:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I've read that the adhesive used to hold them on dissolves with isopropyl alcohol.
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Saturday, November 21, 2009 - 06:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Just pull it off. On the Uly/SS pucks it seems to be easiest to pull from bottom up. : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Roysbuell
Posted on Saturday, November 21, 2009 - 06:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Goo Gone safely removes most adhesives. It comes in a spray that should be able to seep behind the puck.
Top of pagePrevious messageNext messageBottom of page Link to this message

Court
Posted on Saturday, November 21, 2009 - 06:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I saw alcohol used once. . . . alcohol was introduced into the owner for about 4 hours . . he got on the bike and the pucks were removed within 2 miles.

Not the cleanest method . . . but heck it worked.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ourdee
Posted on Saturday, November 21, 2009 - 06:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

because there is not one hitting it's forehead with the palm.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ulyssesmatt
Posted on Saturday, November 21, 2009 - 07:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

From the 2010 factory service manual:

Warning - The aluminum frame of this motorcycle is the fuel tank. Drilling, welding, cutting, grinding, sanding, polishing or other modifications to this frame can weaken it or cause a fire, which could result in death or serious injury. (00126b)

1. To break the adhesive bond, apply isopropyl alcohol along the perimeter edge of the puck at the upper or lower rear corner. Wipe off excess alcohol.

2. Fit fingers under the corner edge and pry to loosen puck.

NOTE: If the puck fit prevents getting finger tips under puck, cover the blade of a putty knife or similar tool with duct tape, to prevent scraping the frame, and pry up one corner of the puck.

3. Slip fingers under the loose corner and slowly pull the puck away from the frame. Apply isopropyl alcohol as needed to loosen remaining adhesive bond.

4. Clean adhesive from painted finish with isopropyl alcohol. Wipe up excess alcohol with cloth.
Top of pagePrevious messageNext messageBottom of page Link to this message

Pogue_mahone
Posted on Saturday, November 21, 2009 - 08:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

WARM it with a heat gun
and
lmao @ Court :P
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration