Author |
Message |
Frosty
| Posted on Monday, February 23, 2009 - 06:22 pm: |
|
Does anyone have page 3-8 of service manual, can't rotate motor without this page. |
Iamarchangel
| Posted on Monday, February 23, 2009 - 07:34 pm: |
|
Which manual? |
H2owerker
| Posted on Monday, February 23, 2009 - 09:42 pm: |
|
And...What instructions are missing? My manual is missing section 1.10 (Drive Belt) so I found someones write-up on here and used that. |
Court
| Posted on Monday, February 23, 2009 - 10:09 pm: |
|
Those are pirated downloads. |
Fastxb12r
| Posted on Monday, February 23, 2009 - 11:09 pm: |
|
ARRR MATEY U BETTER FIND A BETTER DOWNLOAD LIKE I DID....sry couldnt help myself |
Court
| Posted on Tuesday, February 24, 2009 - 06:30 am: |
|
>>>couldnt help myself No problem. It's just stealing, that's all. Some folks do, some folks don't. |
Panhead_dan
| Posted on Tuesday, February 24, 2009 - 11:01 am: |
|
Court, Just to clarify, let's say I had a manual for my '06 XB12X and found it to be missing a few pages or even a chapter. What would be the correct course of action to obtain the missing pages? Thanks in advance for your knowledge, Dan |
Bplass
| Posted on Sunday, March 01, 2009 - 10:56 pm: |
|
You can sign up on Buell's website in the "Owners" section and they have entire manuals for all models. |
Froggy
| Posted on Sunday, March 01, 2009 - 11:37 pm: |
|
Again, those are owners manuals, not the service manuals. |
Skinstains
| Posted on Monday, March 02, 2009 - 12:31 am: |
|
For what year and model ? |
Frosty
| Posted on Tuesday, March 03, 2009 - 06:53 pm: |
|
07 XB9R |
Iamarchangel
| Posted on Tuesday, March 03, 2009 - 07:52 pm: |
|
I'm hoping it's okay to just copy the text from the '05 manual. There's a pic that shows the connections for the fuel line, throttle position sensor and the connection for the injectors. Those are in the rest of the manual. ENGINE ROTATION FOR SERVICE 3.3 GENERAL The following process allows you to rotate engine down, pivoting on rear isolator mount, in order to service components in the top end. NOTE The engine does not need to be removed from chassis in order to perform top end repairs. DISASSEMBLY NOTE Vehicle should be placed onto the lift with rear tire placed in the wheel vise in order to successfully perform this procedure. 1. Disconnect fuel pump and run vehicle until it is out of fuel. NOTES ● This step is always performed in order to purge fuel lines. ● The connection for fuel pump is just above the pump located at the rear of the fuel tank on the left side of the vehicle. 111WWAARRNNININGG To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Remove seat and disconnect battery. 3. Remove intake cover. See 2.34 INTAKE COVER ASSEMBLY. 4. Remove air filter. See 1.15 AIR CLEANER FILTER. 5. Remove air filter base plate. See 4.45 AIRBOX. NOTE The velocity stack has a clamp ring securing it to the throttle body. 6. Remove throttle body velocity stack . 7. Cover induction module to prevent objects from falling into the intake. 8. See Figure 3-1. Disconnect fuel line. 9. Disconnect the throttle position sensor [88]. 10. Disconnect the fuel injector leads [84 & 85]. |
Frosty
| Posted on Sunday, March 08, 2009 - 08:45 pm: |
|
Iamarchangel, I finished rotating motor and removed header. Shipping it to American Sport Bike for ceramic coating. Thanks for the help. |
|