G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » XBoard » Buell XBoard Archives » Archive through May 31, 2008 » Anyone know? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Staindus
Posted on Wednesday, May 28, 2008 - 10:28 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I am trying to find a mount for my radar detector to fit in the threaded hole where my mirror used to be. I found one at this size:

10 mm x 1.25

Will it fit?

I also tried googling badweb and I could not find an answer.

Thanks,
Rob

(Message edited by staindus on May 28, 2008)
Top of pagePrevious messageNext messageBottom of page Link to this message

Firebolt32
Posted on Wednesday, May 28, 2008 - 11:47 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

This here is a bar mount. I know it's not what you looking for but it may help.

http://www.radarbusters.com/search/index.cfm?Ntt=B uell%20Motorcycle%20Mount&Ntk=all
Top of pagePrevious messageNext messageBottom of page Link to this message

Staindus
Posted on Wednesday, May 28, 2008 - 11:51 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Thanks for the link Firebolt32.

This is the place I was looking at (I think its the same product)

http://www.techmounts.com
Top of pagePrevious messageNext messageBottom of page Link to this message

Froglosopher
Posted on Wednesday, May 28, 2008 - 11:52 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Try
ram-mount.com they have mounts for almost anything}
Top of pagePrevious messageNext messageBottom of page Link to this message

Staindus
Posted on Wednesday, May 28, 2008 - 12:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I want to go with techmounts so I can use the threaded hole that my mirrors were in. I have bar ends now. It seems like it would work nicely I just want to make sure the size is right.
Top of pagePrevious messageNext messageBottom of page Link to this message

Firebolt32
Posted on Wednesday, May 28, 2008 - 12:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Your link has more options. But it claims there are not results for your bike...
Top of pagePrevious messageNext messageBottom of page Link to this message

Staindus
Posted on Wednesday, May 28, 2008 - 12:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I know. Either there database is screwed or they have not updated it yet. I am assuming that by Standard "10 mm x 1.25" They mean that most bikes use that size, hopefully including Buell.

(Message edited by staindus on May 29, 2008)
Top of pagePrevious messageNext messageBottom of page Link to this message

Point_doc
Posted on Wednesday, May 28, 2008 - 02:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

When I turned down and threaded the posts from my bar-end mirrors to fit the stock location, I know it was 10mm and I believe the pitch of 1.25 is correct.

You can buy a single bolt with that configuration and check, or take a mirror into your local hardware store and check.

Also I believe the size/pitch is standard, because some Buell owner's have replaced their mirrors with ones off of an Aprilia with no modifications necessary.
Top of pagePrevious messageNext messageBottom of page Link to this message

Retrittion
Posted on Wednesday, May 28, 2008 - 05:24 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

What Aprilia mirrors fit Buell Rs -- I have been trying to figure this out for a while!
Top of pagePrevious messageNext messageBottom of page Link to this message

Point_doc
Posted on Wednesday, May 28, 2008 - 05:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Tuono, I saw these on a Uly.

The first post mentioned 10mm by 1.25 threads, I had the understanding that it was for a posted mirror. Like the ones used on Lighting's, if I created any confusion, sorry.





(Message edited by point_doc on May 28, 2008)

(Message edited by point_doc on May 28, 2008)
Top of pagePrevious messageNext messageBottom of page Link to this message

Staindus
Posted on Thursday, May 29, 2008 - 08:25 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Thanks Point_doc. I will go to the hardware store and check it to be sure.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration