G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » XBoard » Buell XBoard Archives » Archive through January 17, 2006 » Need torque specs asap « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Cliff
Posted on Thursday, January 12, 2006 - 02:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Hi

Can anyone give me the torque specs for the front end ( 04 XB12S )

stem cap (upper tree)
three pinch bolts (upper tree)
four pinch bolts (lower tree)
axle
axle pinch bolts
2 bolts which hold the caliper to the fork

Do these bolts get lock tite ?

I ordered a service manual but it won't be here for a few days and I need to get this done. So if anyone can help me out, I would greatly appreciate it .


Thanks
MaTT
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Thursday, January 12, 2006 - 06:44 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Gotta make it hard on me man. One sec. I'll post them up.
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Thursday, January 12, 2006 - 07:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

stem cap (upper tree)
Ok, the torque on this is 38-42 ft/lbs. No lock tite needed. You are suppose to check the stearing head bearings resistance also. I'm not going into detail on that being I don't have a ton of time right now. Maybe later. But, you can torque it without checking. Might just get some pulsating while breaking, but that's it.

three pinch bolts (upper tree)
Ok. The center bolt is the stem pinch fastener. That needs to be torqued to 17-19 ft/lbs. Use blue lock tite on this.
The other 2 also are 17-19 ft/lbs. with lock tite blue.

Now, I'm going to make myself very clear. If you over torque that area you will crack and break your clamps. Torque it right or break you clamps. You will get no sympathy from me if you do break them from not following the torque specs. Do the job right or don't do it at all.

four pinch bolts (lower tree)
Ok. The lower ones require a torque of 13-15 ft/lbs. with blue lock tite.

Repeating myself: Now, I'm going to make myself very clear. If you over torque that area you will crack and break your clamps. Torque it right or break you clamps. You will get no sympathy from me if you do break them from not following the torque specs. Do the job right or don't do it at all.


axle
The front axle is 39-41 ft/lbs. Use Anti Seize, otherwise you have a bad day. USE IT!!!! Also, the front axle is left hand thread.

axle pinch bolts
Pinch bolts are 20-22 ft/lbs. Torque them slowly and do one, the other, first one, other, etc. Makes the torquing even.


2 bolts which hold the caliper to the fork
This one is 35-37ft/lbs. Use blue lock tite.
Top of pagePrevious messageNext messageBottom of page Link to this message

Cliff
Posted on Thursday, January 12, 2006 - 07:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Thanks Cataract I appreciate it

MaTT
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Friday, January 13, 2006 - 12:26 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

No problem.
Top of pagePrevious messageNext messageBottom of page Link to this message

Elff
Posted on Friday, January 13, 2006 - 12:29 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Darn it
I had run to the garage to get my manual and you were done
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Friday, January 13, 2006 - 10:37 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Darn it
I had run to the garage to get my manual and you were done


Sorry, manual is in my computer room and was on hand. Heck, I had enough time to order a pizza and eat it before I posted this.
Top of pagePrevious messageNext messageBottom of page Link to this message

Elff
Posted on Friday, January 13, 2006 - 12:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

yea yea yea
Did you get a haircut and write your thesis too?
: )
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Friday, January 13, 2006 - 02:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Almost.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration