G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » XBoard » Buell XBoard Archives » Archive through March 12, 2005 » Twice in one week « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Nedwreck
Posted on Friday, March 04, 2005 - 10:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

My bike has been on a trailer. Last saturday for a flat and today because it would not start after I washed it.
It acted funny after the last time I washed it. It ran on one cylinder and eventually started running right but this time, not a sausage.
Is it going to leave me on the side of the road the next time I get caught out in the rain on it? Do I need to wash it very carefully with Handi Wipes from now on?
I'm very careful rinsing the bike off. Where are the spots on an XB one should never aim a hosepipe?

Bob
Top of pagePrevious messageNext messageBottom of page Link to this message

Barkandbite
Posted on Friday, March 04, 2005 - 11:10 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I wash mine weekly and squirt her down with enough
water to fill a small pool. Have for the last 1.5 years.

'course I also use my compressor to blow all the
excess out of where ever it lands...

Does it crank over when you try to start it and
just not catch?

Chris
Top of pagePrevious messageNext messageBottom of page Link to this message

Nedwreck
Posted on Friday, March 04, 2005 - 11:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

It doesn't make a peep. Like it's not getting fire.
Starter spins it just fine. Lots of gas fumes, too.
Oh, well. I'm sure they'll sort it tomorrow.

Bob
Top of pagePrevious messageNext messageBottom of page Link to this message

Barkandbite
Posted on Friday, March 04, 2005 - 11:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Sounds like either the plug wires are shorting
(check for cracks) or the coils are? If you've
got cracks in the boots perhaps the water is
getting in and causing the problem.

In my cars we'll often take out the plug with the
wire attached, ground it and see if we get spark.
You can do the same with your bike, I believe.

If no spark, then you know it's ignition related.

Although, I think you've already established that,
right?

It's not fuel. It's not the starter. It doesn't
seem to be the battery.

Chris
Top of pagePrevious messageNext messageBottom of page Link to this message

M1combat
Posted on Saturday, March 05, 2005 - 01:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Do you wash it with a pressure washer?
Top of pagePrevious messageNext messageBottom of page Link to this message

12bolt
Posted on Saturday, March 05, 2005 - 02:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Bring it in the house for a day, let it dry out then give it a shot!
Top of pagePrevious messageNext messageBottom of page Link to this message

Road_thing
Posted on Saturday, March 05, 2005 - 07:44 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Bob:

Barkin' Chris is probably on the right track. If it were me, I'd pull the leads off the spark plugs, dry the outsides of the plugs and the insides of the caps, and try to start it again.

The spark can jump across the wet porcelain easier than the gap in the cylinder because it's the path of least resistance. I guess it might happen at the coil end of the plug leads, too, although I've personally never seen it.

rt
Top of pagePrevious messageNext messageBottom of page Link to this message

Deuceman
Posted on Saturday, March 05, 2005 - 01:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

A squirt of WD-40 in the boot ends will displace the water if there is any. I have done it before on my Norton, and it didn't hurt anything. I think it would be safe here also. Somebody correct me if I am wrong.
Top of pagePrevious messageNext messageBottom of page Link to this message

Nedwreck
Posted on Saturday, March 05, 2005 - 08:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

M1combat, I don't own a pressure washer.

The tech guy and I took the covers off the right side and pulled the connectors that go to the electronic ignition apart and shot them full of non conductive grease. Changed the plugs as well. Fired right up.

Bob
Top of pagePrevious messageNext messageBottom of page Link to this message

Barkandbite
Posted on Sunday, March 06, 2005 - 01:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Prolly just water in the boots then, eh?

Dialetric grease will help, but at least you've
got a good procedure to try if it happens again.

Chris
Top of pagePrevious messageNext messageBottom of page Link to this message

Dstrat
Posted on Sunday, March 06, 2005 - 11:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

buy some corrosion x, a water displacer, and electrical system protectant...available at aviation supply outlets, or on the net...works great
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration