G oog le Buell 1125R Forum | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » 1125R Superbike Board » BUELL SUBSTITUTE PARTS « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Pwillikers
Posted on Sunday, October 24, 2021 - 08:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Alternatives to Buell OEM parts that are no longer available should be posted in this thread.

Many Buell OEM parts are getting harder and in some cases impossible to find. Please use this thread as a repository for our collective knowledge about alternative parts.

Please keep this THREAD ON TOPIC AND FREE OF DISCUSSION. If you disagree or want to discuss, please start another thread for discussions and then post your conclusions here.

Please don't post an alternative if you're not ABSOLUTELY sure it will function properly.

Please follow the format of the next post and please use the same nomenclature as used in Buell's Official Parts Catalog.

(Message edited by pwillikers on October 25, 2021)
Top of pagePrevious messageNext messageBottom of page Link to this message

Pwillikers
Posted on Sunday, October 24, 2021 - 08:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Buell Part Information: (Official Parts Catalog Description, Part Number, Page Number and, Index Number)
COOLING FAN, Q0060-1AM, page 90, index 12

Alternative Part Information: (Manufacturer, Part Number, Description, Where Obtained)
Spal, 30103013, 5.2" Paddle Blade Pusher Fan, ebay

Notes:
It is a perfect replacement, without modification, for either the left or right side fan. The fan chassis, electrical connectors and lead length are identical to the Buell OEM fan.
Top of pagePrevious messageNext messageBottom of page Link to this message

Pwillikers
Posted on Sunday, October 24, 2021 - 09:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Buell Part Information: (Official Parts Catalog Description, Part Number, Page Number and, Index Number)
REAR BRAKE CALIPER, H0102-1AM, page 58, index 14

Alternative Part Information: (Manufacturer, Part Number, Description, Where Obtained)
Brembo, P32G, brake caliper, ebay

Notes:
I had to do two very simple things to make it a perfect fit:
1. I installed 1.5mm shims (common M8 stainless washers) on the mounting bolts between the caliper and swingarm so the new caliper is exactly centered over the rotor, and
2. The stock brake line matches up perfectly but the OEM caliper uses a banjo bolt with a normal thread pitch and the Brembo caliper uses a fine thread hence you can't reuse the banjo bolt you removed.

The bleeder valve on the Brembo is on the bottom of the caliper when installed as opposed to the top of the caliper where it should be. This is really the only very minor functional difference. I just connected the plumbing and holding the caliper in my hand, turned it upside down so the bleeder was on top, bled the caliper then turned it right side up (bleeder valve down) and installed it. It was actually easier doing it this way than bleeding it in place as you would normally.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ceejay
Posted on Sunday, October 24, 2021 - 09:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If you get the P32F it will have the line inlet and bleeder valve at the topÖ
Top of pagePrevious messageNext messageBottom of page Link to this message

Pwillikers
Posted on Monday, October 25, 2021 - 02:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I am just attempting to consolidate alternative part information in one concise thread.

(Message edited by pwillikers on October 26, 2021)
Top of pagePrevious messageNext messageBottom of page Link to this message

Ceejay
Posted on Monday, October 25, 2021 - 05:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

?
The P32 series by Brembo are used on a lot of bikes. I have the F version on my bike, an 08 1125. Therefore itís a direct replacement. Itís sold by twin moto as a replacement.
I didnít do a write up nor do i care to. It works, and has both the brake line input and the bleed valve at the top when installed.
If you want to make it a post that is only about parts that you approve of then note that please.
Top of pagePrevious messageNext messageBottom of page Link to this message

Pwillikers
Posted on Tuesday, October 26, 2021 - 03:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Corey, Sorry about the tone of my previous post. It came off a lot more cranky than intended.

Apologies.

(Message edited by pwillikers on October 26, 2021)
Top of pagePrevious messageNext messageBottom of page Link to this message

Pwillikers
Posted on Friday, November 12, 2021 - 04:40 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Buell Part Information: (Official Parts Catalog Description, Part Number, Page Number and, Index Number)
Front Brake Lever, H1508-1AM, 55, 11
Clutch Lever, X1202-1AM, 81, 25

Alternative Part Information: (Manufacturer, Part Number, Description, Where Obtained)
Mfg. unknown, PN, unknown, search for: "Motorcycle Adjustable Brake clutch lever Short Long For Buell 1125R 2008-2009, 1125CR 2009" on aliexpress.com, seller: Felizpower

Notes:
Perfect fit, appx. $20. for both levers delivered.

a.jpg



b.jpg
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration