G oog le Buell 1125R Forum | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » 1125R Superbike Board » Archive through February 18, 2016 » Dies when coming off throttle « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Danoz34
Posted on Saturday, November 07, 2015 - 09:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

2008 1125R with EBR ECM.
I have an issue with the bike shutting off when I'm coasting to a stop or I have the bike in gear at low rpm/idle. This will happen when I pull the clutch in to come to a stop either in traffic or like a stop light. It will also "bog" if I'm in gear at low rpm (about 2k to 3K) as I'm decelerating or putting along a neighborhood street. It will run all day in neutral though. I'm not getting any Check Engine Lights either to go off of. TPS percentage shows normal, IAC steps shows good, fuel pressure is good, map shows good. The bike smells like its running rich as well. Does anyone have any ideas for me to test/try before I have to take it out of state to get worked on?
Top of pagePrevious messageNext messageBottom of page Link to this message

Rocketjump
Posted on Sunday, November 08, 2015 - 02:36 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It's probably the EBR ECM and the fuel mapping. On my 1125R I had a Remus tuned ECM from EBR and it would occasionally die when matching rpms on a downshift or revving it in nuetral. Swap out the ECM to stock before you take it out of state.

(Message edited by Rocketjump on November 08, 2015)
Top of pagePrevious messageNext messageBottom of page Link to this message

Danoz34
Posted on Sunday, November 08, 2015 - 09:05 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I bought it with ecm already installed. Is there a way to test the ecm?
Top of pagePrevious messageNext messageBottom of page Link to this message

Willmrx
Posted on Sunday, November 08, 2015 - 10:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I just had they same issue with my friends 2008 1125R. Try disconnecting the clutch switch and see if it stops stalling. It ended up being the clutch switch. Check the live data info on the IC and see what state the clutch is in. It should be one with the lever pulled in and zero with it not pulled in. Good luck.

(Message edited by willmrx on November 08, 2015)
Top of pagePrevious messageNext messageBottom of page Link to this message

Danoz34
Posted on Sunday, November 08, 2015 - 05:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The clutch seems to be working correctly. There seems to be a slight (half a second) delay from going from 1 to 0. It isn't staying stuck in either 1 or 0
Top of pagePrevious messageNext messageBottom of page Link to this message

Willmrx
Posted on Tuesday, November 10, 2015 - 04:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Have you tried to disconnect the clutch switch and see if you still have the issue?
Top of pagePrevious messageNext messageBottom of page Link to this message

Danoz34
Posted on Tuesday, November 10, 2015 - 07:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I will try that and see what it does. What will disconnecting the switch cause to happen?
Top of pagePrevious messageNext messageBottom of page Link to this message

Willmrx
Posted on Wednesday, November 11, 2015 - 09:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The motorcycle will explode. No not much will happen. My buddy put aftermarket clutch lever/ master cylinder on his about three months ago and have had the switch disconnected with no issue.
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Thursday, November 12, 2015 - 12:02 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

While it is not an issue, having the switch disconnected alters how the bike handles deceleration, idle, and taking off from a stop. That in addition to being a safety to prevent you from starting while in gear.
Top of pagePrevious messageNext messageBottom of page Link to this message

Danoz34
Posted on Saturday, November 14, 2015 - 02:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So i disconnected the clutch switch. The bike idles at the normal 1250 to 1500 rpm in neutral. When I put it in gear with clutch it the rpm jumps to 3000 rpm. Is this normal? While riding it never died on me with me stopping but i believe that is because the rpm was so high.
Top of pagePrevious messageNext messageBottom of page Link to this message

Panshovevo
Posted on Sunday, November 15, 2015 - 07:36 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

This is just a shot in the dark, but check the harness connector for the side stand switch (the switch isn't there on domestic bikes, but the harness is) and see if the termination plug is in place.

I'll try to pull one of mine today and see if it is a resistor or not.

Edited to add I checked, it's basically just a weather plug near as I can tell.
Missed the target on this one.



(Message edited by Panshovevo on November 16, 2015)
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration