G oog le Buell 1125R Forum | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » 1125R Superbike Board » Archive through July 29, 2012 » Electric specs 4 aftermarket turn signals? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Duphuckincati
Posted on Tuesday, July 17, 2012 - 11:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'd like to change mirrors on my CR so need to go aftermarket turn signals. Checked the manuals with no luck, what are the electrics specs needed to just do a replacement without additional relays or whatever? And/or anyone found some that work already?
Top of pagePrevious messageNext messageBottom of page Link to this message

Dannybuell
Posted on Tuesday, July 17, 2012 - 11:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I used another set of rear arrow signals for the front on my CR. nothing to know the connectors are the same. reminds me of my S1's oem set up, front and rear the same.
Top of pagePrevious messageNext messageBottom of page Link to this message

Duphuckincati
Posted on Tuesday, July 17, 2012 - 11:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Good idea. I'd prefer to go with flush mount types but not locked into it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Wednesday, July 18, 2012 - 11:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Any led indicators will work but your signals lights will flash faster due to the lower current of the smaller aftermarket indicators.

I put these which are tiny. I drilled a hole in the black plastic just behind the headlight to mount them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Nuts4mc
Posted on Wednesday, July 18, 2012 - 01:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Flashers that compensate for the low drain of LEDs - go here:

http://www.customled.com/

the rice burner crowd around here uses them...I don't know where the flasher is on the 1125r - might want to check the "pin" configuration before you order...
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Wednesday, July 18, 2012 - 01:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

don't know where the flasher is on the 1125r -

In the Instrument pod =)
}
Top of pagePrevious messageNext messageBottom of page Link to this message

Ros
Posted on Thursday, July 19, 2012 - 03:11 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

When I changed my turn signals to the rizoma blinkers, and a flush mount from the front ones, I need to install the resistors(??) that came with the rizoma's to lower the blinker speed.

Top of pagePrevious messageNext messageBottom of page Link to this message

Noobuel
Posted on Thursday, July 19, 2012 - 11:15 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I thought I read somewhere (may have been BuellXB.com) that the flasher in the IC adjusted to LED indicators once the bike was running, but flashed at a higher rate while it was on in accessory mode?
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration