G oog le Buell 1125R Forum | Login/out | Topics | Search | Custodians | Register | Edit Profile Ads by Motorcycle.comMotorcycle InsuranceMotorcycle PartsMotorcycle Helmets Motorcycle Tires Buell Motorcycles

Author Message   Zecca Posted on Tuesday, March 13, 2012 - 07:34 pm:        OMG! actually it is ridiculous! today had nothing to do and I decided to play with Kevlar What do you think? I cut in half? paint it black? discard in the trash? haha   Jdugger Posted on Tuesday, March 13, 2012 - 08:15 pm:        Looks like someone threw an omelet (or a pancake) on your stator...   Reepicheep Posted on Tuesday, March 13, 2012 - 08:37 pm:        I remember those from that star trek episode! Scary stuff... the flying egg thingies...   Nuts4mc Posted on Tuesday, March 13, 2012 - 09:07 pm:        if you could get it to transfer heat- paint it black - you'd sell 5000 of them!   Dannybuell Posted on Tuesday, March 13, 2012 - 09:14 pm:        what holds it on?   Bartone Posted on Tuesday, March 13, 2012 - 09:46 pm:        Wouldn't cutting it in half and doubling the thickness of the bottom be better? I doubt you would ever damage the upper portion of the cover. And yes.. paint it.   Zecca Posted on Thursday, March 15, 2012 - 09:28 am:        "what holds it on?" I made an aluminum slider, the outside is larger than inside... 1 millimeter the pieces fit together with pressure.. I did a drawing as my cover was already damaged for safety I used a bit of high temperature silicone now got better, not much, I cut in half and coated with carbon fiber   Xtreme6669 Posted on Thursday, March 15, 2012 - 10:08 am:        I think that looks pretty good! Bet it cost ya a lot less than the EBR ones!   Zecca Posted on Thursday, March 15, 2012 - 10:29 am:        + or - $30 hehe   Dannybuell Posted on Thursday, March 15, 2012 - 11:39 am:        Are you going to test it to make sure it stays on or do you see this as purely cosmetic?   Finedaddy1 Posted on Thursday, March 15, 2012 - 12:28 pm:        I like it, i'd buy one. Good job!   C818919 Posted on Friday, March 16, 2012 - 01:35 am:        i have + or - $30 bucks   Zecca Posted on Friday, March 16, 2012 - 09:15 am:        if I lived in U.S. would be worth for you!   S21125r Posted on Friday, March 16, 2012 - 10:05 am:        I'd be inclined to epoxy it to the aluminum slider. Stock aluminum clutch side slider seem to stay in place during low sides so I can't see why the stator side would act much differently. Only exception that I can think of is if the who assembly spun counter clockwise during a crash so that the carbon bit was @ 12:00 instead of 6:00. Ribs in the stator cover should help prevent that rotation though. Or... if there is an excessive air gap between the AL cover and the carbon cover then a low side might tend to lever the whole slider assembly out of it's bore. For an every day street rider though this might be "good enough". Nice work!   Zecca Posted on Friday, March 16, 2012 - 11:19 am:        I tried to hit with a rubber hammer! believe, I hit strong in all directions! stayed in place i'll only be sure in a lowside I thought about screw the cover on the slider...what do you think?   Fio835 Posted on Friday, March 16, 2012 - 11:20 am:        Airbrush it! haha   Dannybuell Posted on Friday, March 16, 2012 - 11:45 am:        using a bolt and some sort of alignment device would be very interesting.

Add Your Message Here Post: -Color- Black Red Green Blue Yellow Purple Orange Cyan Gray White -Font- Arial Courier Symbol Times Verdana -Size- Smallest (-2) Small (-1) Normal Large (+1) Largest (+2) Username: Posting Information: This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional. Password: E-mail: Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.) Enable HTML code in message Automatically activate URLs in message Action: