G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » Buell RACING & More » Racing - Drag Racing » Give me some input here guys « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Budgolf
Posted on Thursday, January 26, 2012 - 05:44 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

While getting ready to order my new engine kill I realized that my EBR ECM doesn't have the side stand kill enabled. Which is where I was going to wire the kill. So this opens up a couple of things I can do. I can send my ECM back to EBR for reprogramming, or I can use my stock ECM and a new powercommander. I'm really leaning toward the power commander and old ECM because of the tune ability it offers.

On a side note, my rear valve cover has been leaking for a while and I'm going to fix that when I do the valve adjustment in a couple of weeks. Question is, doesn't EBR have some base and head gaskets that bump the compression ratio up a couple of points? I know I read that somewhere. Think the increase in power would be worth the trouble?
Top of pagePrevious messageNext messageBottom of page Link to this message

Williep13
Posted on Friday, January 27, 2012 - 08:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If this is just a regular tethered engine kill it should just have two wires that you wire in series with your kill switch on your handle bar. This way when you pull the tether it kills the bike just like turning the switch off.

I am not sure on an 1125 motor but on the evo motors you can just leave the base gasket of and use silicone gasket (very thin coat) to serve that purpose. This is not recommended on a bike that you ride but drag racing where most likely you will tear it apart at least yearly a lot of people do this.

Hope this helps.
Top of pagePrevious messageNext messageBottom of page Link to this message

Budgolf
Posted on Friday, January 27, 2012 - 10:13 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks Willie, the engine kill Im talking about is for the air shifter. Which I guess would be clear if I called it what it is. Thats another benefit to the power commander. in addition to all the tuning it provides, It can be set to kill the fuel and works really well with the nc2 nitrous controller.

the bike is still going to be a daily driver, so I'm going to need gaskets. I have heard of people tossing them tho.
Top of pagePrevious messageNext messageBottom of page Link to this message

Littlebutquick
Posted on Friday, January 27, 2012 - 02:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

have you the ABS still on your bike you could use that for your kill
Top of pagePrevious messageNext messageBottom of page Link to this message

Budgolf
Posted on Friday, January 27, 2012 - 04:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ABS?
Top of pagePrevious messageNext messageBottom of page Link to this message

Slaughter
Posted on Friday, January 27, 2012 - 04:25 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Bank Angle Sensor (or tip over switch). Use those wires for your kill. They are used for the quick shifter in the ECM.
Top of pagePrevious messageNext messageBottom of page Link to this message

Littlebutquick
Posted on Friday, January 27, 2012 - 05:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

yes thats right i can find out the pin number that plugs in the ecm if you need it
Top of pagePrevious messageNext messageBottom of page Link to this message

Budgolf
Posted on Friday, January 27, 2012 - 09:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks guys! That's why I love this place!
Top of pagePrevious messageNext messageBottom of page Link to this message

Littlebutquick
Posted on Sunday, January 29, 2012 - 03:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

PIN 17 0N THE GREY PLUG THAT GOES TO THE ECM
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration