G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » Ecmdroid « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Sprintex
Posted on Saturday, October 26, 2019 - 04:25 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I trying to reset the TPS on my 06 it hasn't been check in 23K I now have 30K. when trying to reset the TPD to 0 it will not go below 1.3. And of course the bike now runs like shit. It was running fine before I touched it. Shit.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sprintex
Posted on Saturday, October 26, 2019 - 06:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ECM Will not give me the settings in real time, I have to keep turning on and off and it gives me different readings.
I used Froggy directions but everything and the simple ones from ECMDROID.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sprintex
Posted on Sunday, October 27, 2019 - 12:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

This was using Buelltooth. Also now I have no live data. NO RPM or TPS voltage I can turn on the fan so it kind of works.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Sunday, October 27, 2019 - 12:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'm afraid I can't help with the electronics but before you reset the tps, if you haven't already, make sure your butterfly is clean along with the bore. Any build up along the bore or edges of the butterfly will affect getting the throttle to true zero. It's best to set it with the engine hot so if it's running bad and you finally get the electronics to work you might want to reset it cold, then ride it and reset it again while hot. If you already know all this then disregard and carry on.

I'm sure somebody will answer your questions soon. The weekends are kind of slow for answers.
Top of pagePrevious messageNext messageBottom of page Link to this message

Shoggin
Posted on Sunday, October 27, 2019 - 01:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If the live data freezes on ECMDroid, hit the grey button on the lower left that says "Live Data Off".

I know... it's counter-intuitive
Top of pagePrevious messageNext messageBottom of page Link to this message

Sprintex
Posted on Sunday, October 27, 2019 - 04:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Does it matter how far you back off the idle screw? I back out a lot but them you could not hear the butter fly snap shut so I turned it back in till I could.
Thanks for the hints, just another learning experience. I just got done getting a 1997 Guzzi Centauro back running after being off the road for 16 years learn a lot about FI on that one.
Top of pagePrevious messageNext messageBottom of page Link to this message

Steveford
Posted on Sunday, October 27, 2019 - 05:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Get maximum slop in the throttle cables, snap the throttle open/shut three times, back off the idle adjuster screw until the voltage goes as far down as it will go and then back off one additional turn.
Hold the throttle shut and then do Reset TPS, Reset AFV, take the slop out of the cables and adjust the idle cable until it reads 4.8V (I believe that is, I'm doing this from memory).
The factory training had us do it on a cold engine, there was no mention about a hot motor.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sprintex
Posted on Monday, October 28, 2019 - 06:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

What is the AFV. I used these instructions from Bulltooth
https://www.buelltooth.com/perform-tps-reset.html
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Monday, October 28, 2019 - 10:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Air Fuel Value. It will use this value to richen or lean the fuel according to your O2 sensor.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mark_weiss
Posted on Tuesday, October 29, 2019 - 01:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Adaptive Fuel Value. The ECM contains a fuel control map that determines how much fuel is injected at any one time. The AFV number is a percentage by which the ECM alters the standard map so that fuel supplied matches measured conditions.

When I ride to San Diego my AFV goes up to 100% to match the atmospheric condions at sea level. When I am in Flagstaff my AFV goes down to 90 to avoid running too rich at 7000 feet.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sprintex
Posted on Wednesday, October 30, 2019 - 03:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Okay all set. A good friend said to get the butterfly almost stuck so there is a little resistance when opened , this i did plus I cleaned the butterfly really good. It worked! Happy Happy Joy Joy.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration