G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through October 21, 2011 » ECM protection « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through October 16, 2011Skifastbadly30 10-16-11  12:25 pm
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Skifastbadly
Posted on Sunday, October 16, 2011 - 05:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Motorbike, I tried to follow you on the one bolt in the top bracket but I didn't understand it. I tried something else and I'd like to hear the collective's opinion. So, same front bracket, but for the rear what I did was put a couple of layers of gorilla tape on the end of the ECM, then ran a zip tie down through the original bracket mounting hole, then through the ECM mounting hole (which is now beneath the bracket) and cinched it up tight. This way it should experience no 'free' vibration and the tape should protect the ECM. Looks like this:

ECM Relo


I left the zip tie untrimmed only so it was clearer on the photo, then I clipped it.

(Message edited by skifastbadly on October 16, 2011)
Top of pagePrevious messageNext messageBottom of page Link to this message

Growl
Posted on Monday, October 17, 2011 - 02:16 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I was hopeful when Froggy wrote that this ECM thing is a non issue for 2006 models but checked mine anyway. I have a 2007 seat and it was rubbing... Seat and ECM have rub marks and the wiring was chaffed. I bent the metal ECM support bracket down out of the way and made a thick leather backing for the ECM. It lays nice and low in there now. The leather prevents the ECM from contacting anything. I wrapped a second piece of leather around the wires... All held together with zip ties. The support block (with a spacer instead of ECM) is still there to support seat. Will post pic soon...
Top of pagePrevious messageNext messageBottom of page Link to this message

Growl
Posted on Monday, October 17, 2011 - 11:40 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Here is the ECM relocated slightly, mounted on a backing of leather which prevents it from being able to rub on anything hard... the yellow arrows point to zip ties and the blue arrow points at the seat support block mounted at original location (ie the original front ecm mount point) only with washers taking up the space the ecm used to...


ULY ECM relocated


I wrapped a second piece of leather around the wires to protect from further chaffing.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hughlysses
Posted on Monday, October 17, 2011 - 01:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Never had an issue on my 07 with the factory-installed spacer under the front bolt.

When I updated to the 09 engine, wiring harness and ECM, after the first long ride I noticed I now had a problem. The CONNECTORS are what's noticeably larger on the 08-up ECM. The seat was pressing on the front connector and had already cracked the sealant around the plug on the ECM. I took a piece of scrap steel 1" x ~1/16" material I had lying around and made this:


1



2


I bolted it at the rear using what looks like a spare threaded hole in the battery support box and rested the front on the seat block. This provides a good 1/8" clearance from the bottom of the steel bar to the front connector, and keeps the seat off the rear connector as well. Not real pretty, but it works.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellerxt
Posted on Monday, October 17, 2011 - 03:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Good solutions Growl and Hugh. Very helpful pictures and explanations. Thanks. I'll monitor my ecm and hope my 'cruder' solution continues to work. If not, I'll be looking to do something like you guys did.

I like your solutions as well, Ski and Pont. Good job starting this thread, Pont. Very helpful to a lot of folks, I'm sure. Thanks.
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnshore
Posted on Tuesday, October 18, 2011 - 10:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

A friend made this.

<img>
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnshore
Posted on Tuesday, October 18, 2011 - 10:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

A friend made this for me. About 7000 miles ago. This is it new. Its got lots of scuff marks on it now.




Top of pagePrevious messageNext messageBottom of page Link to this message

Schwara
Posted on Tuesday, October 18, 2011 - 10:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've got the sister to that one and she seems to be holding up just fine. I did go ahead and mummify the ECM in silicone tape (thought I saw a hairline crack) and I added the spacer block in addition as well. If I still manage to kill the ECM then I have to lose some weight before spending any more money on the Uly.
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnshore
Posted on Wednesday, October 19, 2011 - 06:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

After several thousand miles under my fat ass.

« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration