G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through April 07, 2010 » Spare gas / Tool tube install « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Unrealtrip
Posted on Wednesday, March 24, 2010 - 11:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Didn't really take any pix of the actual install process, fairly straightforward, these little puppies bolt straight up with 5/16"'s 1" bolts, some washers and locknuts. I carry inside each of them a 33oz msr fuel bottle full of... fuel which gets me just under a half gallon of spare gas. It's not a ton, but hey, it'll get me another 20-25 miles.

Anyway, here's a few pix of the installed tubes, they are quite secure, waterproof, rattle free and completely out of the way.







Invisible from the front


note: You will need to grind the edges down on four washers for the inside as they will need to fit inside a channel.

(Message edited by unrealtrip on March 24, 2010)
Top of pagePrevious messageNext messageBottom of page Link to this message

Tbolt_pilot
Posted on Thursday, March 25, 2010 - 01:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Rockets!!!

No, seriously, those are cool. I've been thinking of doing something like that out of a stainless water bottle for my 9S. Do those have any kind of lock?
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikef5000
Posted on Thursday, March 25, 2010 - 09:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

FYI some Xylene or goof off will take the paint off.

Looks good!
Top of pagePrevious messageNext messageBottom of page Link to this message

Liv2
Posted on Thursday, March 25, 2010 - 12:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I'm going to mount mine to the rack like Dr. Greg, so I will be able to have them on the bike if I leave the cases off. I just can't justify the expense of the hardware that Dr. Greg used, although it is top quality and looks good. I've seen some other hardware ideas posted here that I may try.
Top of pagePrevious messageNext messageBottom of page Link to this message

Electraglider_1997
Posted on Thursday, March 25, 2010 - 12:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Mount some amber lights on those things for a nice set of turn signals.
Top of pagePrevious messageNext messageBottom of page Link to this message

Towpro
Posted on Thursday, March 25, 2010 - 01:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I did the same mount as Dr Greg, only used 75c clips from Home Depot. 100 miles this weekend, with some large potholes (that covered the whole road) and my tubes did not spin. The tubes are even useful for day to day riding. I have been putting store bought plastic water bottles in them. (plus I enjoy the reactions from by buddies when I unscrew the lid and pull out the water bottle for a drink).

I was thinking of buying some of that reflective tape and cutting a piece to fit on the lids, and maybe a strip down the sides. You would not see this tape while standing next to the bike, but 20' away it's going to light up when a car hits you with the head lights.
Top of pagePrevious messageNext messageBottom of page Link to this message

Unrealtrip
Posted on Thursday, March 25, 2010 - 02:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

What is the Dr. Greg mount? Link?

n/m found it
http://www.badweatherbikers.com/buell/messages/142838/546522.html?1268459544


(Message edited by unrealtrip on March 25, 2010)

Just got done rubbing off all the yellow on them and reading Dr. Greg's mounting solution and Tow's alternate one. I had considered mounting them to the frame as well, but I wasn't sure about the idea of them being closer to the swingarm and being able to potentially pivot, though it appears you guys have no problem with it that way either.

(Message edited by unrealtrip on March 25, 2010)
Top of pagePrevious messageNext messageBottom of page Link to this message

Dr_greg
Posted on Thursday, March 25, 2010 - 03:24 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

C'mon, pony up, guys! A classy bike like the Uly DESERVES that fancy-dancy mounting hardware!

--Doc
Top of pagePrevious messageNext messageBottom of page Link to this message

Matchanu
Posted on Friday, March 26, 2010 - 04:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I did mine like yours, only I added two more to the back of the cases as well.

It looks like they were supposed to be there.
Top of pagePrevious messageNext messageBottom of page Link to this message

Whisperstealth
Posted on Friday, March 26, 2010 - 04:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Towpro, Where in Home Depot did you find the clips?

Doc, she deserves em sure, but she deserves tires and gas more: )

THE OPERATORS TUBE: GOD'S GIFT TO BIKERS, AND A SWEET OBSESSION ON BWB!
Top of pagePrevious messageNext messageBottom of page Link to this message

Unrealtrip
Posted on Friday, March 26, 2010 - 04:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I did mine like yours, only I added two more to the back of the cases as well.

Can you take a picture? I looked at the back of the case method but couldn't get it to line up very well.}
Top of pagePrevious messageNext messageBottom of page Link to this message

Ratbuell
Posted on Friday, March 26, 2010 - 06:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Another alternative to the "rubbing the yellow off" method is to get a can of Fusion plastic paint in texture black. Spray it on, looks factory, doesn't chip (at least, not before I got my Uly and the tubes re-covered in muck!).

If you just want to pull the yellow off, spray it with brake cleaner and wipe. Comes right off.
Top of pagePrevious messageNext messageBottom of page Link to this message

Towpro
Posted on Friday, March 26, 2010 - 07:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Whisper, they were in the electrical area, the same area where you find zip ties. They come 2 in a bag, with the cardboard piece shown below in the bag.
They come in different sizes. I think they were hanging on a wall, in the bags. I also think contact cleaner is found in the same place. I think they use 1/4" bolts.

Top of pagePrevious messageNext messageBottom of page Link to this message

Tbolt_pilot
Posted on Saturday, March 27, 2010 - 01:10 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I just used a few of those exact clamps recently. One for the clutch cable, the overflow tubes, wiring, etc. They are sturdy enough to hold but will bend just enough not to bind anything. Plus the rubber prevents chaffing. I hate chaffing, it gives me a rash.
Top of pagePrevious messageNext messageBottom of page Link to this message

Matchanu
Posted on Monday, March 29, 2010 - 01:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Unrealtrip:

You have to shave the upper and lower tabs and drill some new mounting holes to make it fit.

Use a hack saw, takes all of 5 minutes.

Much easier to get to, I use one of them for a tool roll.

I'll see if I can get some pictures.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration