Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Staves
| Posted on Thursday, June 04, 2009 - 11:34 am: |
|
I've been waiting on delivery of a good Torx T-27 socket to use for a clutch cable replacement and primary oil change. It isn't here yet and I really want to get this done before leaving for Homecoming tomorrow AM. Am I asking for a headache attempting this job with the wimpy Torx key that comes in the tool kit? Any opinion welcome. Thanks (as always). |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Froggy
| Posted on Thursday, June 04, 2009 - 11:40 am: |
|
I find the toolkit one to be useful, it can get into places my socket one can't like to remove the screws on the left side scoop. I haven't used it for the clutch cable, so I don't know if it is good for that. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Pso
| Posted on Thursday, June 04, 2009 - 11:52 am: |
|
It has worked for me. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Staves
| Posted on Thursday, June 04, 2009 - 11:57 am: |
|
I'll give it a shot. I might be the guy spouting primary fluid at Homecoming ![](http://www.badweatherbikers.com/buell/clipart/eek.gif) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Mnrider
| Posted on Thursday, June 04, 2009 - 12:04 pm: |
|
I bought a 1/4 inch drive t27 at the auto parts store for 4 bucks then use an ext. or 1/4 drive handle,and you can put it in your tool bag |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Thetable
| Posted on Thursday, June 04, 2009 - 01:41 pm: |
|
quote:I bought a 1/4 inch drive t27 at the auto parts store for 4 bucks
I did the same. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dr_greg
| Posted on Thursday, June 04, 2009 - 02:19 pm: |
|
After rounding off a couple "auto parts store" T27s, I ordered one from a German supplier. So far so good. --Doc |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Sparky
| Posted on Thursday, June 04, 2009 - 03:07 pm: |
|
I bought a regular Craftsman T27 screwdriver. It just fits in a cranny in the right side of the space under the rear seat. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Svh
| Posted on Thursday, June 04, 2009 - 03:18 pm: |
|
I was at Home Depot and found a 1/4" drive Torx set that had a T27 and use that. Can't recall the price though |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rwcfrank
| Posted on Thursday, June 04, 2009 - 03:38 pm: |
|
Buy a quality brand torx bit or regret it..Dont ask me how I know...I went with Snap On after 2 auto parts store brands.. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Etennuly
| Posted on Thursday, June 04, 2009 - 04:55 pm: |
|
The key to using any torx bit is keeping pressure pushing in and keeping it straight in. Most of the times that my employees break or round a torx bit they are not holding it properly. It must stay perpendicular to the bolt head, especially at the time of maximum torque, 'breaking it loose'. That little T27 wrench in the kit, albeit a slow method, will work well if held correctly. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Florida_lime
| Posted on Thursday, June 04, 2009 - 07:47 pm: |
|
As mentioned, the toolkit piece will work in some places that others won't. After rounding off a couple "auto parts store" T27s, I ordered one from a German supplier. So far so good. --Doc Most of the time I use my Wiha T-handle Torx set. (Message edited by florida_lime on June 04, 2009) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Routney
| Posted on Thursday, June 04, 2009 - 10:36 pm: |
|
There's a bunch of good options out there. I completely agree with the folks recommending better quality tools. For my bike, I try to have what I need on the bike. Here's what I put together: http://www.routney.com/Blog/files/edcfaea94a48d557 0086215f05ea18eb-26.html |