G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through August 18, 2008 » Checking oil « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Allthegoodonesrtkn
Posted on Monday, August 11, 2008 - 02:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I check my oil level with the bike on the kick stand, is this correct. Or should it be checked upright on a rear wheel stand? I didnt see anything in the manual about this.
Top of pagePrevious messageNext messageBottom of page Link to this message

Dr_greg
Posted on Monday, August 11, 2008 - 02:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

It should be on the side stand; engine warm. Surely it's in the manual...
Top of pagePrevious messageNext messageBottom of page Link to this message

Etennuly
Posted on Monday, August 11, 2008 - 02:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Best to ride it for a while, five miles or so. On the side stand. Oil level is best at lower two or three X"s on the bottom of the stick.
Top of pagePrevious messageNext messageBottom of page Link to this message

Greenamp
Posted on Monday, August 11, 2008 - 02:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Keep in mind too that even if your warm oil level is in the "add" section, it is only about 1/8th of a quart low.
Top of pagePrevious messageNext messageBottom of page Link to this message

Allthegoodonesrtkn
Posted on Monday, August 11, 2008 - 02:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I knew about the oil being warm, its mentioned in the manual. But I dont remember the sidestand or rear stand being mention when checking oil levels. The oil is around the bottom two x's also, and seems not to move from these levels. But when the oil is changed and the oil levels are at the max, the bike seems to us oil until it gets to the last two x's. Anyone else experiance this. And why do these bike use oil?
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Monday, August 11, 2008 - 02:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Yes, 2 x's is the happy spot. Any more it will just burn it off : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Greenamp
Posted on Monday, August 11, 2008 - 04:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

They don't really use oil in the classic sense, but tend to blow it in to the airbox, burning some indirectly through the intake.
Top of pagePrevious messageNext messageBottom of page Link to this message

Red_chili
Posted on Monday, August 11, 2008 - 04:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

And greasing your sensor and throttle body nicely.
Top of pagePrevious messageNext messageBottom of page Link to this message

Etennuly
Posted on Monday, August 11, 2008 - 07:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

A good while back there were several threads concerning the high usage of oil on the Uly's. It was found that the guys trying to keep the oil at the full mark on the stick were the ones with the problem. When it is down to the lower end of the stick it will stay there for a long time before needing to add any oil.

The excess oil was found lying around inside the airbox. The more oil that was added to keep it at the top marks, was all the more oil in the air box. So it is not using or burning the oil, it is just pumping it into the air box.

When I change my oil I put in 2.5 quarts. Where that ends up on the stick is what I consider full. That is about the second X on the stick. My '06 has over 30,000 miles on it now and only uses about a half of a quart between changes that I do at 3,000 mile intervals. It is about the same as when it was new.
Top of pagePrevious messageNext messageBottom of page Link to this message

Joenuclear
Posted on Wednesday, August 13, 2008 - 08:39 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Depending on your weight and the appropiate suspension sttings the angle of the bike on the side stand can change quite a bit. Or as they say on T.V. "I'm just saying".
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnboy777
Posted on Wednesday, August 13, 2008 - 09:46 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Top of pagePrevious messageNext messageBottom of page Link to this message

Electraglider_1997
Posted on Wednesday, August 13, 2008 - 10:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Are you timing the blister speed?
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnboy777
Posted on Wednesday, August 13, 2008 - 10:31 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

""Are you timing the blister speed?""

Checking the oil level HOT ... yeah, you really have to 'man up', but you do get an accurate reading. It should just cover the finger nail.

.
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnboy777
Posted on Wednesday, August 13, 2008 - 10:44 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Maybe next time, I'll check it cold!

« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration